The standard bathtub drain size is generally 1. 5”, which is the size of the drain opening and the pipe leading from the bathtub. The bath trap, the part of the drain that is located under the tub, must be a minimum of 2” although 2.
25” or larger is recommended if the installation is located in an area that requires a backwater valve. The bathtub overflow drain is typically 1. 25” in diameter. Additionally, it’s important to note that the total drain line may comprise a combination of 1.
5” and 1. 25” sections. This is typically so the overflow drain can tie into a larger drain line leading outside of the home.
Can you use 1 1 2 pipe for tub drain?
The standard plumbing setup for a tub drain involves the use of two pipes: a 1. 5-inch drainpipe and a 2-inch vent pipe. It is possible to use a single 1. 5-inch pipe as the drainpipe, but a 2-inch vent pipe should also be included, otherwise the drainpipe may not be able to relieve pressure from the trap seal.
If one pipe is used, the tub drain-overflow should be higher than the drainpipe’s centerline, usually about six inches. Additionally, the pipe may need to extend farther into the wall or ceiling to provide access to the drainpipe in case of a clog.
However, It is strongly recommended to use two pipes when installing a tub drain, as this provides a better balance of plumbing pressures which encourages smoother drainage in the drainage system. Furthermore, installing a single pipe may not comply with local plumbing regulations.
Can I use a 1 1 2 drain for a shower?
Yes, you can use a 1 1 2 drain for a shower. This size of drain is generally considered to be adequate for most standard showers. However, it is important to consider the size of the shower area, the number of fixtures and the flow capacity of the pipe before selecting the size of the drain.
The drain should have an adequate flow capacity to quickly and efficiently discharge the water load from the shower area. Additionally, a drain with a higher flow capacity may be beneficial if the shower area is relatively large or has multiple fixtures.
It is also important to ensure that the drain will fit in the area where it is to be installed and that it is compatible with the pipe used in the installation.
Do all bathtubs have the same size drain?
No, bathtubs do not all have the same size drain. In fact, there is quite a variety of bathtub drains available, ranging in size from 2 inches to 4 inches in diameter. The size needed depends on the size of the bathtub and the type of bathtub you have, as some bathtubs require a specific size of drain.
Additionally, some bathtubs have different types of drains, such as an overflow type drain, requiring an additional adapter. If installing a new bathtub, you should check the manufacturer’s instructions to get the correct size to ensure proper operation.
When replacing an existing drain, it is recommended that you match the size already present in your bathtub, as changing the size could lead to a poor fit and a potential for water leakage.
What size PVC is used for tub drain?
Most residential bathtub drains are outfitted with 1 1/2-inch PVC pipe. That is the most commonly used size, although tub drains ranging from 1 1/4-inch to 2-inch pipe may also be used, depending on the drain assembly setup and the bathtub materials.
It is important to note that the size of the PVC pipe is actually refers to the size of the inside diameter of the pipe, so a 1 1/2-inch piece of pipe has an outside diameter of 1. 9 inches. No matter the size, all PVC pipe used for tub drains must meet ASTM standard D-1784.
Can you replace just the tub drain?
Yes, it is possible to replace just the tub drain without needing to purchase a whole new tub. The best way to go about replacing just the drain is to first disconnect the drain assembly from the waste line, then take the old drain to a hardware store to find a matching one.
Once the new drain is purchased, use plumbers putty and a wrench to loosen the old flange and then install the new drain by tightening the nuts and screwing it into the wall. After installing the drain, reattach the waste line and check for any leaks.
How do you measure a bathtub drain size?
Measuring the size of a bathtub drain is an important step when replacing a bathtub drain stopper. Before you can measure the size, decide if you will be using a drop-in or a snap-in style drain stopper.
If your existing drain is covered, remove any screws or clips on the sides of the drain to reveal the size you need.
Using a ruler or measuring tape, measure the outer edge of the drain from the bottom of the drain to the top where it meets the tub. This measurement is called the drain flange size.
Next, measure the inside diameter of the drain pipe. To do this you will need to insert the measuring device into the pipe. Make sure to measure the entire length of the drain pipe, starting at the bottom and ending at the bathtub floor.
Lastly, you will need to measure the hole in the bathtub. This is the size of the hole that the new drain will fit into. Using a ruler or measuring tape, measure the diameter of the hole at the bathtub surface.
Once you have taken all of these measurements, use them to choose the correct size drain stopper that matches the measurements of the bathtub drain.
What are the three standard sizes for bathtubs?
The three standard sizes for bathtubs are 30 inches, 60 inches, and 72 inches in width. 30 inch bathtubs are the most popular size for small bathrooms and can fit almost any alcove. 60 inch bathtubs are the most popular size for larger bathrooms and offer plenty of room for two people.
72 inch bathtubs are ideal for very large bathrooms and usually come in luxury models. When it comes to length, the standard bathtub length is 60 inches for all sizes, however, some luxury jacuzzi style baths may come in even longer sizes such as 72 inches.
Are shower and tub drains the same size?
No, shower and tub drains are not the same size. Shower drains are typically smaller than tub drains due to the fact that showers require more frequent draining, and the sewer line that the drain serves may be smaller.
Shower drains are usually two to four inches in diameter, whereas tub drains are usually two-inch diameter. Additionally, shower drains may come with a strainer to collect hair and other debris, which reduces the size of the drain opening.
For that reason, depending on the type of strainer, a shower drain may look a lot smaller than a tub drain opening.
What is the minimum size pipe for a shower drain?
The minimum size pipe recommended for a shower drain is 2 inches in diameter. This size is large enough to handle the amount of water that is present in most showers. Additionally, the walls of a 2-inch pipe are thick enough to handle any shifting or settling of the pipe during installation.
A 2-inch pipe is also small enough that the amount of space it takes up in the walls or floors of your home is minimal.
What is the minimum size of the fixture supply pipe for a bathtub?
The minimum size of the fixture supply pipe for a bathtub is usually 1/2 inch in diameter. However, the plumbing code in your area may require a larger size for your tub, so it is important to check your local regulations.
A larger supply pipe size will ensure a greater water flow rate and may be warranted if your tub is particularly large or you have more than one fixture in close proximity. If you live in an area requiring larger diameters than 1/2 inch, the most common sizes are 3/4 inch and 1 inch.
Additionally, other factors such as pressure, the length of the pipe, and the height elevation should also be taken into consideration when choosing the size of your fixture supply pipe.
What size drain pipe should I use?
The size of the drain pipe you should use depends on what type of drainage system you’re creating and what kind of waste it’s intended to hold.
For underground drainage systems, the minimum size you should use is a 3” or 4” diameter pipe. A larger pipe is necessary if multiple fixtures are connected to the system, such as multiple showers, sinks or other drainage.
The size of the pipe should correspond to the total water volume that is expected to flow through the system.
For above-ground drainage systems, a 2” pipe is usually sufficient for most residential applications. However, for high-volume systems such as residential swimming pools or landscape drainage, larger pipes should be used — either 3” or 4” diameter.
When installing a drain pipe, it’s important to consider the compatibility of the pipe material to the type of waste being carried and the geographical area you’re in. For instance, places with extremely cold temperatures may need a pipe that won’t freeze, such as PVC or ABS.
And areas located near the ocean may require a material that can resist corrosion from seawater, such as copper or stainless steel. This is why it is best to consult a professional plumber or contractor to determine the best type of drain pipe to use for your specific project.
Can a bathroom sink drain 1 1 2?
Yes, a bathroom sink drain can accommodate 1 1/2″ pipe. This is typically the standard size for sink drains. Additionally, larger 1 1/2″ tubular drains are also available and can be used in vanity sinks.
When choosing a sink drain, be sure to measure the hole size in your sink and purchase a drain fitting that corresponds with the measurements. Using plumber’s putty and silicone adhesive can help ensure a secure fit.
Also, be sure to check the type of material your drain fitting is made of, as some materials are less resistant to corrosion than others.
Are most tub drains universal?
No, most tub drains are not universal, with some minor exceptions. The variety of types and sizes of drains on the market makes it difficult to establish a true universal drain. Some drain manufacturers will make compatible drains that allow you to select different sizes and styles that will fit many different applications.
Some standardized drain manufacturers will provide cross-compatibility charts which may be used to help in identifying compatible parts and configurations. Most commonly, the tub drain size is determined by the size of the pipe used for the drain.
Standard sizes tend to be 1. 5 inches for drain pipes, however there are other sizes available such as 1-1/4, 1-1/2, 2 and 3-inch drains pipes. The drain flange also needs to be compatible with the tub and must be either slip fit or threaded, most commonly the slip fit flange is used on underslung tubs.
The other components of a bathtub drains system also need to be compatible, such as the tub spout, tub overflow, and drain parts. In some cases, a combination of parts may be required in order to get the desired drain configuration.
Are there different types of bathtub drains?
Yes, there are several different types of bathtub drains. The type of drain you choose will depend on the size of your bathtub and the style you prefer. Typical bathtub drains include toe-touch, lift-and-turn, pull-and-plug, trip-lever, and pop-up drains.
Toe-touch drains are operated by pressing a toe or foot-activated lever near the drain. Lift-and-turn drains are a classic style that you operate by lifting the stopper and turning it to seal or open the drain.
Pull-and-plug drains are the traditional stopper style, which you open and close by pulling and pushing a plug on the end of a rod. Trip-lever drains use a two-part system with a lever handle and plug, which are linked by a chain.
Pop-up drains use a plunger-like handle which you activate to seal and open the drain.
There are also specialty drain products such as grid drains, linear drains, and washlet drains. Grid drains boast a highly efficient, low-profile design and are popular for showers or tiled bathrooms.
Linear drains are designed to allow water to drain along the entire length of the drain and are perfect for marble countertops or tile floors. Washlet drains are long, rectangular drains that are usually installed under the seat of a “Washlet” style toilet and use a unique water stream to clean away waste.
No matter what type of bathtub drain you choose, there are many options available to suit your individual needs and aesthetic tastes.