For the best results, use a soft cloth or a sponge and a mild, non-abrasive cleaner. BathFitter surfaces are made from a high-gloss acrylic, so you should only use cleaning products specifically formulated for this type of surface.
These cleaners will help prevent the accumulation of mildew, soap scum, and mineral deposits. Additionally, you should regularly wipe down your bath and shower walls with a cloth dampened with warm water.
Some specially formulated cleaning products may contain ingredients to keep your surfaces looking glossy and new, while also repelling pollutants.
What not to use on Bath Fitter?
Generally, you should avoid using anything with ammonia, abrasive cleaners, bleach, or scouring materials on your Bath Fitter products. Ammonia-based or other harsh cleaners can fade the color or damage the surface of the product.
Bleach can cause discoloration over time, while abrasive cleaners and scouring materials can damage the surface of your Bath Fitter surfaces. Additionally, you should avoid harsh, abrasive brushes and scrubbers.
These can create marks and scratches on the face of your Bath Fitter product. The best way to clean your Bath Fitter products is to use a soft cloth, warm soapy water, and a mild, non-abrasive detergent.
Can I use magic eraser on Bath Fitter tub?
No, you should not use a magic eraser on a Bath Fitter tub. The Bath Fitter tub is manufactured from high-grade acrylic, which can be easily scratched and damaged by abrasive substances such as the ones found in magic erasers.
The cleaning agents and other chemicals found in these types of erasers can also corrode the acrylic, leaving it discolored and susceptible to further damage. Additionally, it could also cause discoloration of the sealant around the edges of the tub.
The best way to clean and maintain your Bath Fitter tub is to use a mild soap and warm water. If you have stubborn stains, you may use a non-abrasive cleaner specifically designed for acrylic surfaces.
What cleaners are safe on acrylic?
When cleaning acrylic surfaces, it is important to use a cleaner that is safe for use on acrylic. The best type of cleaners to use on acrylic surfaces are non-abrasive and pH-neutral. Examples of non-abrasive cleaners include those without ammonia, bleach, and acids.
Instead, look for cleaners that have gentle detergents and surfactants, and avoid using scouring pads and abrasive scrubbing pads.
To clean acrylic surfaces, use a soft cloth such as a microfiber cloth, sponge, or even a cotton chamois, and lightly dampen it with warm water. To remove tougher grime or dirt, use a non-abrasive soap, such as a dish detergent, avoiding any cleaner that has ammonia, bleach, or acids.
Once you’ve finished cleaning, be sure to use a soft, dry cloth to buff away any residue. If there are water spots or streaks left behind, use an acrylic cleaner specifically designed for use on acrylic surfaces.
While this step isn’t necessary for basic cleaning, it will help keep your acrylic surfaces looking like new.
Is Bath Fitter easy to clean?
Yes, Bath Fitter products are easy to clean and maintain. The material used to make the products is non-porous, making it stain and mold resistant. This prevents moisture and dirt from building up and making it difficult to get it clean.
The smooth, non-porous surface of the products also means that dirt and grime is easily wiped away with a damp cloth. In most cases, all you will need to use is a mild soap solution and rinse it off with clean water.
It also helps that most Bath Fitter products come with a special protective sealer to keep them looking new for years.
How long does Bath Fitter last?
Bath Fitter products are designed and manufactured to last a lifetime. The company backs all of its products with a limited lifetime warranty, meaning that you can expect any product you purchase to uphold its quality and integrity throughout the years.
All of their products are made with the highest quality materials, and they are engineered to stand up to the test of time and offer long-lasting durability. Additionally, they are rigorously tested using a variety of methods to ensure that their products remain safe and reliable.
With proper care and maintenance, your Bath Fitter products should last for many years and give you peace of mind that your home will remain both comfortable and beautiful.
Can magic eraser be used on acrylic?
Yes, a magic eraser can be used on acrylic, as long as the application is gentle. As with any surface, it is important to test the product on a small, less visible area first, to ensure that it will not damage the acrylic.
It is also important to make sure that the eraser is dry and that it is kept moving over the acrylic surface while being used. Using a back-and-forth motion may help remove stubborn dirt and grime from the surface without marring it.
When using a magic eraser, it is important to make sure that excess water does not remain on the acrylic surface after use. Excess water left on the acrylic could cloud its finish and lead to staining.
Does Bathfitters have a lifetime warranty?
Yes, Bathfitters offers a lifetime warranty on many of their products. Bathfitter’s lifetime warranty covers wall surrounds, vanity tops, bathtub liners, bathtubs, and shower liners for as long as you are the original owner(s) of the product.
This means that you are covered for replacements and repairs if any of these products becomes damaged or worn due to normal wear and tear, even decades after the product was installed.
The warranty also covers a comprehensive list of items that are part of the installation process. This includes caulking, adhesives and sealants, shower and tub fixtures, and fixtures for accessories.
The warranty also covers all manufacturer defects of the products that are part of the installation.
Any repairs or replacements that are necessary due to this warranty are done at no extra cost to the customer. Bathfitters will also cover the costs of labor and materials required for any repairs and/or replacements.
However, this warranty does not cover any damages due to misuse, abuse, or neglect.
If you need to take advantage of the warranty, you can either contact the local Bathfitters dealer in your area or contact the Bathfitters headquarters directly. They can help you start the process by providing the necessary information that you will need.
What is the average cost of a Bath Fitter conversion?
The average cost of a Bath Fitter conversion will depend on a variety of factors including size of the existing bathtub, finish and style of product selected, the complexity of the installation and local labor rates.
Generally, you can expect to spend between $1,500 and $5,000 on a typical full Bath Fitter conversion, however, smaller conversions may cost as little as $800 and more extensive baths can cost upwards of $7,000.
It’s best to get in touch with a local Bath Fitter representative to get an accurate estimate for the installation.
Are freestanding baths hard to clean around?
Depending on the specific design of the freestanding bath, it may take a bit more effort to clean around it compared to a bathtub fixed to the wall. Freestanding baths usually have a curved back and can extend as far out as 5 to 6 feet, and so if not kept clean regularly, it can be difficult to access all areas of the bath and clean them thoroughly, especially if the bath is situated in a corner or against a wall.
Fortunately, there are many cleaning products specifically designed to make the job easier, such as long-handled scrubbing brushes and sponges. The L-shaped design of a freestanding bath also means that dirt and grime can accumulate at the bottom corners, so it’s important to make sure those areas are cleaned regularly too.
Can Bath Fitter change tub to shower?
Yes, Bath Fitter can change your existing tub to a shower. Depending on the size and shape of your bathroom, you may be able to convert your bathtub into a shower without replacing it. Bath Fitter offers a full range of bathtub and shower renovations that can transform your bathroom into your own personal sanctuary.
Their services include custom shower installations, tub-to-shower conversions, and bathtub liners. All products are designed to fit around your existing fixtures and plumbing, and they offer professional installation by experienced, certified installers.
Their baths and showers come in a variety of sizes and styles, so you can find something that fits your needs and coordinates with the overall look of your bathroom.
Does Bath Fitter replace faucets?
No, Bath Fitter does not replace faucets. Bath Fitter specializes in custom bath remodeling and installs a wide variety of bathtub wall surrounds, shower liners and bath to shower conversions. Bath Fitter does not install or replace faucets and other plumbing-related items, such as showerheads, toilets, or sinks.
To replace a faucet, it is recommended to contact a licensed plumber, who can provide the necessary services and ensure that all parts are of the highest quality and correctly installed. During the installation, the plumber will be able to answer any of your questions and provide advice and insight on the project you’re undertaking.
What should you not use on an acrylic tub?
It is important to not use any harsh chemicals or abrasive scrubbers on an acrylic tub, as this could cause scratches which will eventually lead to deterioration to the acrylic finish. Additionally, products that contain chlorine bleach or ammonia should be avoided as these could damage the tub finish or create hazardous fumes.
When cleaning an acrylic tub, you should use gentle, non-abrasive, non-chemically based cleaners. For example, mild soap, white vinegar, and hydrogen peroxide are all suitable for use. Generally, a soft cloth or non-abrasive sponge should be used to wipe the tub down, and a dedicated bathroom scrub brush or brush-stiff sponge should be used to scrub any hard to remove areas.
Avoid using any hard bristled scrub brushes or brushes with hard plastic edges, as these can scratch or leave marks on the tub’s surface. It is also important to rinse the tub thoroughly with clean water after cleaning to prevent a soap scum build up.
Can I clean acrylic with Windex?
Yes, Windex can be used to clean acrylic. As with other cleaning solutions, Windex should never be used in excess – it’s best to apply a minimal amount of Windex and remove it immediately with a damp cloth to avoid over-saturation.
Always test Windex on a small, hidden area to check for discoloration before applying to the entire surface. Using a gentle circular motion, wipe the area with the cloth and Windex. If there are stubborn spots that won’t come off easily, you can apply a bit extra to the cloth and make sure the cloth is not overly wet.
For the best results, make sure to immediately buff afterwards with a dry microfiber or lint-free cloth.
How do you clean acrylic items?
When cleaning acrylic items, it is important to select cleaning products and materials that are designed specifically for use with acrylic. Using regular household cleaners, such as window cleaners and abrasive scrubbers, may damage acrylic, causing it to become discolored and scratched.
The best way to clean acrylic items is to first dust the surface with a soft, lint-free cloth. This will remove any dirt and other loose particles from the surface.
Next, you can use a mild detergent, diluted in water, and a soft cloth to gently scrub the surface. If the item has intricate details, it is best to use a slightly dampened cotton swab. Rinse the area with clean water and carefully dry with a soft, cloth.
To ensure the surface remains streak-free, use one side of the cloth to wipe away the moisture and then buff with the other side of the cloth.
If there are stubborn stains, you can use a very dilute solution of isopropyl alcohol in water. Put a few drops into a clean cloth and gently rub the stained area until the stain is removed. Rinse the area with water and dry the surface with a clean cloth.
When cleaning the surface of your acrylic item, avoid using harsh chemicals like bleach, ammonia, and vinegar as these can discolor and damage acrylic. It is also important to never clean acrylic items with abrasive materials, such as steel wool, scouring pads, and sandpaper.