Small toilets are toilets specifically designed for smaller spaces in bathrooms. They may be shorter in depth than standard toilets, and may have either a round or elongated bowl. Small toilets typically use a smaller tank than standard toilets, maximizing space and making it easier to fit where space is limited.
Since it uses a smaller tank, it also uses less water than a regular toilet. Small toilets often come with special features like extra arm support for comfort and a low-profile design for easier access.
They can be found in a variety of colors and styles to match any bathroom’s décor. Small toilets are perfect for those with limited bathroom space, or those who intend to install a toilet in an area with only minimal clearance.
They also tend to be more affordable than standard size toilets, making them an ideal option for those on a budget.
What is a lowboy toilet?
A lowboy toilet is a type of toilet typically found in older homes or in commercial buildings. This type of toilet sits a lower than traditional toilets and usually sits upon four legs. Lowboy toilets generally use a single flush and have an elongated bowl shape.
These toilets are usually considered old-fashioned, and most people today have switched to a newer, more modern style of toilet. Lowboy toilets are still common, however, in both new and old homes, especially in rural areas or locations with limited resources.
In many cases, replacing a lowboy toilet with a newer model can require considerable plumbing work and can be quite expensive.
How do I choose a small bathroom toilet?
Choosing a small toilet for a bathroom can seem a bit overwhelming given the plethora of options on the market. However, with a bit of research, comparison shopping, and measuring the room, you can find the perfect toilet for your bathroom.
First, make sure to measure the room to determine the maximum dimensions the toilet can have. This will help you narrow down your choices to only units that will fit in the space without being too cramped.
Measure the width of the area available, the depth for the tank, and the height of the bowl.
Next, think about your personal needs and any family needs that have to be taken into consideration. A good example of this might be a family that requires a low-sitting toilet with a higher seat height to assist those with mobility issues.
Other considerations include how much water is used in a full flush, the style, and the type of flushing system.
Once you determine both the size and needs of the toilet, it’s time to start comparing brands, reviews, and cost. As much as you may be tempted to choose the very smallest model, remember that if the flushing system is weak or it requires multiple flushes to clear away waste, you won’t save any water.
This can also mean more trips to the store to buy costly replacement parts.
Finally, be sure to read the product specs and any customer reviews to get a better idea of the quality and the level of customer satisfaction. Spending a bit extra for a quality product is usually worth it.
You don’t want to purchase a small toilet only to find out that it won’t last more than a few years.
By following this guide, you should have no problem finding the perfect small toilet for your bathroom. With a bit of research, comparison shopping, and measuring the room, you’ll have the perfect new toilet in no time.
Are tall or short toilets better?
The answer to this question depends on a few different factors. Short toilets, with a height of between 14-15 inches, are thought to be comfortable and accessible to most people, as they don’t require as much stretching or exertion to use.
But, taller toilets, usually 16-17 inches (or sometimes even higher, up to 19 inches or more) may be preferable for those who have difficulty sitting down and standing up. Taller toilets provide greater leverage and leverage can make it easier for those with mobility issues to transition from standing to sitting and vice versa.
Additionally, taller toilets may help to reduce straining, which can be problematic for those with certain medical conditions. While it ultimately comes down to personal preference, you might consider the needs of anyone who will be using the toilet to determine if taller or shorter is best for your household.
Are all American Standard toilets the same size?
No, all American Standard toilets are not the same size; there is a variety of sizes available for purchase. The two most common sizes for American Standard toilets are Comfort Height and Standard Height, with Comfort Height toilets being higher than Standard Height toilets.
The size, or rough-in, of all American Standard toilets is universal, which is 12” and most likely fits the distance between the wall and the drainage hole. However, bowl size and tank size vary widely.
The main differences between toilet bowl size include the length of the bowl, the shape, and the width of the opening. The gallons per flush and type of flush are also very important factors to consider when selecting toilet size.
There are also a variety of tank sizes and shapes, such as elongated and round front models, and one-piece versus two-piece models. American Standard also offers wall-mounted toilets for those who prefer a modern look, as well as compact and ADA compliant toilets for those with special needs.
Ultimately, there are a wide variety of options available from American Standard toilets to fit any bathroom size, style, and function.
How do I know which American Standard toilet I have?
The best way to determine which American Standard toilet you have is by looking at the model number that is printed on the inside of the tank lid. The model number can typically be located on a sticker or ink stamp that should be clearly visible.
It is important to note that the model number may not be the same as the description you have heard about the toilet. Also, some American Standard toilet models have the same model numbers, though there may be some minor style differences.
Once you have the model number, you can compare it to a list of toilets from American Standard to determine which one you have.
How do I know if my toilet is 10 or 12?
If your toilet is a standard residential model, you can usually tell if it is a 10 or 12 inch model by measuring the distance between the bolts that hold the toilet to the floor. To do this, remove the toilet lid and look at the bolts on the side.
Measure the distance between the two bolts and this should tell you the width of your toilet. If the distance is 10 inches, it is a 10 inch toilet, and if the distance is 12 inches, it is a 12 inch toilet.
If you have an older or non-standard model, you can measure the exterior of the bowl from one side of the rim to the other to determine your toilet’s width. It is also important to note that the distance between the bolts may not equal the bowl width, so always measure the exterior for an accurate measurement.
Are all toilets 12 inches from wall?
No, not all toilets are 12 inches from the wall. The exact distance is determined by the type of toilet you have. Depending on the size, shape and model of the toilet, the distance from the wall can range from 10-14 inches.
For standard toilets, the recommended distance is 12 inches. Keep in mind that this distance is also often determined by the type of toilet seat you have installed. Wall hung toilets, for example, will naturally be closer to the wall than other models.
Since this distance can vary, it’s important to take accurate measurements before installing a new toilet in your bathroom.
Is my toilet a 2 inch or 3 inch?
The answer to your question depends on what type of toilet you have installed. Generally speaking, most residential toilets are equipped with either a 2-inch or 3-inch flush valve, but this could vary depending on the age and model of the toilet.
To be sure, it is best to remove the tank lid and check the flush valve at the bottom of the tank. A 2-inch flush valve will have a small ring that surrounds the outlet port of the valve, whereas a 3-inch flush valve will have a larger ring with three lugs.
If you are having difficulty identifying the size of your flush valve, it may be helpful to take a photo and share it with a plumber or home improvement store for verification.
What is considered comfort height for a toilet?
Comfort height toilets generally measure 17 to 19 inches in height, compared to the standard toilet height of just over 15 inches. This height is similar to that of a standard kitchen chair and is considered easier to sit on and stand up from.
Comfort height toilets can be beneficial for seniors, those with mobility issues and taller individuals. Companies often market these toilets as “chair height” or “right height” models. While comfort height toilets can be helpful for those with mobility issues, it is important to note that this height does not always suit individuals of all ages and heights.
It is usually a good idea to try out the toilet before purchasing it.
What measurements do I need when buying a new toilet?
When shopping for a new toilet, there are several measurements that you need to consider. To ensure a proper fit in your bathroom space, you should measure the rough-in distance. This is the distance between the wall and the center of the waste outlet.
A standard rough-in for residential toilets is 12”. If you have limited space, you should check for toilets with a 10” or 8” rough-in. Additionally, you should measure the length of the existing bathroom space from the wall to the seat position, which will indicate the length of the toilet.
Other measurements that should be taken include the width of the tank and the width of the bowl. The toilet must fit in the allotted space, accounting for the flange and the base of the toilet. Lastly, you should measure the distance from the floor to the underside of the toilet, which determines the height.
Consider a comfort height toilet, which is designed to be 17-19” high. With all these measurements, you should have no problem finding a toilet that fits properly in your bathroom.
How do you tell if your toilet is standard or elongated?
In order to determine if your toilet is a standard or elongated model, you will need to measure the distance between the mounting bolts on the back of the toilet. If these two mounting bolts are between 10 and 14 inches apart, this indicates that the toilet is a standard model.
However, if these measurements are between 18 and 20 inches apart, this indicates that the toilet is an elongated model. Additionally, an elongated toilet bowl is typically 2 to 3 inches longer than a standard bowl.
This can also be used as an indication in determining if a toilet is standard or elongated.
How do you read a toilet size?
Reading a toilet size is relatively easy, however, the exact dimensions may vary depending on the make and model. Generally, toilets are sized by the length of their bowls and the width of their tanks.
To read a toilet size, first measure the length of the bowl from the side of the toilet to the back of the bowl. This is usually between 25 and 28 inches, though it may be a bit shorter or longer depending on the model.
Next, measure the width of the tank – this is usually around 13 to 15 inches wide, but again may vary by model. The measurements together tell you the size of the toilet; for example, a toilet measuring 25 inches in length and 14 inches in width would be marked as 25 x 14.
How are toilet sizes measured?
Toilet sizes are typically measured in two ways: rough-in size and outside dimension. The rough-in size is the distance from a wall to the center of the hold-down bolt hole. This is an important factor when deciding what toilet to buy because it will determine if a toilet will fit in the space available.
Outside dimension is simply a measure of the length of the toilet bowl, typically between 15 and 30 inches. Generally, the longer the toilet the more comfort it will provide. It is important to measure both the rough-in size and outside dimension of a toilet before buying it so that you can ensure that it will fit your bathroom space.
How do you measure the height of a toilet?
Measuring the height of a toilet accurately requires a few tools and a bit of effort. To start, you’ll need to gather a tape measure, level, and either a toilet flange or level platform.
First, you should measure the ground at the point where the toilet will be installed. With the level, mark the place where the water shut-off valve will go. With the level platform or toilet flange in place over that same point, measure the height of the platform or flange.
This will give you the height of the toilet bowl.
Next, you’ll need to measure the height of the tank. With the level platform in place, position the tank directly above the flange and measure its height. To ensure accuracy, make sure the tank is always level.
Finally, to get the total height of the toilet, simply add the bowl height and the tank height together. This will give you the height of the toilet from the floor, allowing you to make sure it’s the correct height when installed.