The distance between the wall and the toilet typically depends on the model of toilet being installed. Most toilets should be between 12” to 15” away from the wall, but there may be variations depending on the size of the space, the base setup, and other factors.
The easiest way to ensure that the toilet is correctly placed away from the wall is to look at the specific instructions that are included in the toilet installation manual. If the instructions are not available, it is highly recommended to contact a professional plumber or bathroom installer to ensure that the toilet is correctly and safely installed.
How do you measure a toilet off the wall?
When measuring a toilet off the wall, you first need to gather the necessary supplies, such as a measuring tape, a level, a pencil, and a screwdriver. Once you have all the supplies, start by locating the screws that hold the toilet to the wall.
Depending on the model, the screws may be located at the top and bottom of the toilet, under the bowl, or behind the toilet seat. Once you have located the screws, you can use the screwdriver to loosen and remove them from the wall.
Next, you need to measure the distance from the wall to the back of the toilet tank. To do this, you can use a measuring tape and measure from the wall to the side of the toilet tank. Make sure to take an accurate measurement and write it down on a piece of paper.
Then, take a level and set it on the floor behind the toilet, making sure it is even with the wall. Finally, use the level to measure the distance from the floor to the back of the tank. You can then add these two measurements together to get the total measurement of the toilet off the wall.
Are all toilets 12 inches from wall?
No, not all toilets are 12 inches from the wall. The standard toilet rough-in size is 12 inches from the finished wall to the center of the toilet drain. This is the most common toilet rough-in size, but it is not the only size available.
Some toilets are available with a 10 inch, 14 inch, or even 15 inch rough-in distance. The rough-in distance is the amount of space between the rear of the toilet and the finished wall. So if you have more room in the bathroom, you may want to choose a larger rough-in size.
If space is limited in the bathroom, then a smaller rough-in size may be a better option.
How do you measure rough-in distance for a toilet?
Rough-in distance is the distance between the finished wall surface behind the toilet and the center of the toilet’s waste outlet. To measure the rough-in distance, you will need to measure the distance in inches.
Start by measuring the distance from the finished wall behind the toilet (typically 12” away) to the center of the drain hole and write it down. If you are installing a new toilet, you will need to purchase a wax ring in the appropriate size.
To determine the size you need, subtract 3” from the rough-in distance measurement. This number is the size wax ring you will need, with most wax rings ranging from 4” to 12”. If you are replacing an existing toilet, mark the location of the nearest wall stud and use an adjustable toilet mounting flange.
Measure the distance from the center of the mounting flange to the center of the drain hole or centerline of the waste outlet and write it down. This distance will be your rough-in distance measurement.
How do I know if my toilet is 10 or 12?
Determining the size of a toilet bowl can be tricky to do without the proper measurements and tools. To begin, make sure the toilet is disconnected from its water supply. Once the toilet is drained, check the measurements of the toilet bowl either with a measuring tape or a ruler.
Measure the length, width, and height of the bowl to determine the size. Generally, the length of a 10 inch toilet is roughly 25 to 28 inches, while the length of a 12 inch toilet is generally 28 to 31 inches.
It is important to also take into account the height of the toilet as this may vary depending on the model. Additionally, if you are unable to take the measurements yourself, the manufacturer should be able to provide the measurements for the product.
Can you replace a 10 inch rough in toilet with a 12 inch?
Yes, it is possible to replace a 10 inch rough in toilet with a 12 inch, but it is recommended that you proceed with caution. This is because a greater rough in size usually requires a longer toilet bowl and different wax rings.
In addition to checking the fitting of the bolts, it is essential to check for any piping or flooring that may need to be raised or moved due to the increase in toilet length. It is also important to know if your bathroom is able to accommodate the extra length, because this may require countertop modifications.
Ultimately, it is best to consult with a professional plumber to confirm that your plumbing can handle the extra size, and to determine what additional adjustments may be required to install the new toilet.
Should a toilet be touching the wall?
No, toilets should not be touching the wall. Ideally, they should be spaced away from walls by at least an inch or two. This will help prevent damage to the walls due to water build-up or a leaking wax seal.
In addition, having the toilet spaced away from the wall will allow for a more comfortable wiping experience, as well as a more hygienic space. When installing a new toilet, it is highly recommended to spacer off the back wall by at least 1” or 5mm and make sure it is level with the floor.
Also, check the floor and wall tiles for any damage before installation and make sure they are fixed if required.
What does 12 inch rough-in mean when installing a toilet?
12 inch rough-in means the distance from the wall behind the toilet to the center of the waste outlet of the toilet. This measurement is important when installing a toilet because it determines the type of toilet that will fit into the bathroom space and plumbing configuration.
It is important to take accurate measurements when installing a toilet to ensure the toilet is located at the correct distance from the wall, or else the toilet won’t fit against the wall and a longer wax ring may need to be used.
Additionally, the toilet bowl must fit properly on the flange in order to seal the connection. When selecting a toilet, it is important to check the rough-in specifications to determine if it will be compatible with the existing plumbing.
What is code for distance around a toilet?
The code for distance around a toilet typically depends on the building code that applies to the particular area. Generally speaking, for commercial and industrial applications, the minimum distance from any wall to the centerline of a toilet may vary from 24″- 36″ from the center to the wall, and from the centerline of the toilet to the other fixtures may vary from 15″-18″.
For residential applications, the typical distance from the center of the toilet to the wall is typically 12″ while the distance from the centerline of the toilet to other fixtures is 6″. In either case, there should be a clear, unobstructed path to the toilet seat.
Additionally, there may be additional requirements governing the minimum distance between the walls and fixtures of individual toilet stalls. It is best to consult with local code enforcement agencies to determine the specific requirements applicable in a particular area or jurisdiction.
What measurement do I need to replace a toilet?
In order to replace a toilet, you will need to measure the rough-in, which is the distance between the wall behind the toilet and the center of the closet bolts. The rough-in for most modern toilets is 12 inches, but it can vary from 10 to 14 inches.
You should also measure the distance from the back wall to the center of the supply stop (the shutoff valve), which should be about 6 inches. Additionally, you need to measure the width of the existing toilet base, which should be around 16.
5 inches, and the length of the tank, which is usually a bit longer at around 20. 5 inches. Finally, you should measure the height of the bowl, which should be around 15 inches. Knowing all of these dimensions will help when you go to purchase a new toilet and ensure it will fit in the space.
Can you replace a toilet with any size toilet?
No, you cannot replace a toilet with any size toilet. The size of the toilet you need to replace it with depends on the size of your existing toilet and the space you have available in your bathroom.
Moreover, your existing plumbing will also determine what size toilet you can install. Smaller toilets require less space but if your existing plumbing cannot accommodate a smaller toilet, a larger model would be required.
The general sizes available are:
• Round Bowl Toilet: This is between 10 and 14 inches in diameter and 28-30 inches long.
• Compact Elongated Bowl Toilet: This is between 12 and 14 inches in diameter and 28-30 inches long.
• Standard Elongated Bowl Toilet: This is between 14 and 15 inches in diameter and 31-32 inches long.
Before replacing your toilet, it is important to measure the diameter and height of the current toilet, as well as the rough-in measurement. The rough-in measurement is the distance between the wall and the center of the flange (or the bolt caps) which anchor the toilet to the floor.
This usually ranges between 10-14 inches.
Furthermore, when selecting a new toilet, it is important to consider the width of the bowl, the distance from the toilet seat to the back wall, the space needed around the toilet to allow clearance for cleaning and the height of your toilet.
Taller toilets may make it easier for some users to get up and down and are ideal for those with physical disabilities. In general, it is best to select a toilet that is similar in size and style to your current one as this will ensure a successful installation.
Why would I want an elongated toilet bowl?
An elongated toilet bowl offers several advantages that may make it a desirable choice for your bathroom:
1) Increased Comfort: An elongated toilet bowl is typically longer than a round one, providing extra room and a more comfortable seating position. This can be especially helpful for those who may struggle to use a traditional, round-shaped toilet, such as elderly or disabled individuals.
2) Improved Aesthetics: Due to its shape, the elongated toilet bowl can help create a more modern and sophisticated look to your bathroom. This can be especially beneficial if you’re looking for a more stylish, contemporary design for your home’s interior.
3) Compact Size: Despite their larger size, elongated toilet bowls are often shorter than traditional round bowls. This means they can be a great space-saving option for smaller bathrooms, or for anyone who wants to make the most of their available space.
4) Easier Cleaning: An elongated toilet bowl typically features an easier-to-clean design, thanks to its inward curving sides. This design makes it easier to access and reach the various nooks and crannies of the bowl, making it a breeze to keep your toilet clean and hygienic.
In summary, an elongated toilet bowl could be a great choice if you’re looking for extra comfort, enhanced aesthetics, a compact size, and convenient cleaning options.
Are there toilets that sit closer to the wall?
Yes, there are toilets that sit closer to the wall. Many toilets now come with adjustable closet flanges that can be mounted on the wall, allowing for closer installation to the wall than ever before.
In addition, there are a variety of models of wall hung toilets, also known as suspended toilets, that extend just a few inches away from the wall. Wall hung toilets are unique in that all plumbing fixtures and flush mechanisms are hidden, resulting in an ultra-modern, minimalist aesthetic.
Can a toilet be moved closer to the wall?
Yes, it is possible to move a toilet closer to the wall. To do this, you will need a few basic tools. First, you will need a wax ring, which is a large, circular gasket that helps seal the toilet bowl to the floor.
Next, you will need a putty knife to help spread the wax evenly and seal the joint. Finally, you will need a tool to disconnect the water supply, such as a wrench or pliers. Once you have all the necessary tools, you can proceed with the task.
Start by turning off the water supply and disconnecting the water line from the toilet. Then, use the putty knife to loosen and remove the wax seal from the base of the toilet. Now, it is time to lift the toilet off the floor.
Be sure to have help and lift the toilet carefully so as not to break it. Place it in its desired new location, and then install the new wax ring and secure it to the floor with the putty knife. Finally, reconnect the water line and turn the water supply back on.
What’s the difference between a 10 inch rough in a 12 inch rough in toilet?
The main difference between a 10 inch rough in and a 12 inch rough in toilet is the distance from the wall behind the toilet to the center of the closet bolts. With a 10 inch rough in toilet, the distance between the wall and the center of the bolts is 10 inches, while a 12 inch rough in toilet will have 12 inches between the wall and the center of the bolts.
It is important to take your rough in measurement when installing a new toilet since the bolts in the back must be positioned accurately in order for the toilet to sit flush against the floor. If you try to install a 10 inch rough in toilet with a 12 inch rough, you may need to buy closet bolts with an extension kit and, more likely, the toilet will not sit flush against the floor due to the misalignment of the bolts.
The reverse is also true; if you install a 12 inch rough in toilet with a 10 inch rough, you will end up with a small gap behind the toilet where it doesn’t sit completely against the wall.
It is important to measure the rough in with a measuring tape and verify whether it is a 10 inch or 12 inch rough in before purchasing a new toilet.