Removing a toilet from an RV camper is not overly difficult, however, it will take some time and effort. Before you begin, you should always turn off the water supply to the toilet, and disconnect any electrical wiring.
The first step is to remove the caps from the floor and the rear section of the toilet. After this, use a screwdriver to unscrew the bolts from the subfloor and the mounting screws from the sides of the toilet.
You may need an adjustable wrench if the bolt heads are too large to fit with a standard screwdriver. Once the screws are removed, rock the toilet back and forth until it’s free from the subfloor.
Next, if the existing toilet is a gravity model, disconnect the rubber seal from the outlet pipe and remove the toilet alone. If the toilet is a pressure flush, you will need to locate the inlet valve, disconnect the flexible hose and disconnect the inlet valve.
Once the old toilet is removed, seal the opening with putty tape, and make sure to cover any corners and gaps. If a new toilet is being installed, this is the time to install it by following the instructions on the package.
If you’ve opted to keep the same toilet model, re-install the toilet and tighten the mounting screws.
Make sure to reconnect any inlet valves, the flexible hose and the rubber seal, and turn the water supply back on. Finally, ensure the toilet is secure, and all the bolts have been tightened to ensure a leak-proof seal.
How do I remove my RV toilet?
Removing an RV toilet is a relatively simple task. Before starting, make sure you have the right supplies and tools to help complete the task.
First, begin by disconnecting the water supply lines and draining any remaining water in the tank. You want to make sure that all the water is removed prior to beginning the toilet removal. Next, loosen the two hold-down bolts that secure the toilet base to the floor.
Once the bolts are removed, use a pry bar to gently lift the toilet from the floor, being careful not to damage the waste pipe or any other plumbing in the process.
The toilet will now be free from the floor. You can now remove the connections between the toilet and the waste and water supply lines. Depending on your RV model, you may need to disconnect the toilet from the black water tank as well.
Have a bucket ready to catch any excess water if needed.
The final step is to carefully lift and remove the toilet from the RV, being very careful not to damage any surface of the RV or the internal components.
Removing an RV toilet is a relatively easy task that anyone can complete with the right supplies and tools. With these steps, you will have successfully removed your RV toilet in no time.
Can I remove a toilet myself?
Yes, you can remove a toilet yourself with the right tools. It can be helpful to have a friend or family member assist you. First, shut off the water supply to the toilet and disconnect the supply line from the tank.
Flush the toilet until all water is out of the tank and bowl, then disconnect the siphon hose. You’ll then need to disconnect the toilet bolts located on the floor by the toilet. Remove any caulk or sealant and carefully lift the toilet off the floor.
Take special care while removing the toilet, as they can be very heavy and unwieldy. Once the toilet is out of the bathroom, you’ll need to use a sponge or shop vacuum to remove any remaining water from the drain.
You may need to unscrew the nuts from the closet flange or wax ring and potentially replace them. Be sure to dispose of the toilet properly at a disposal site or have it hauled away.
Can you replace RV toilet with regular toilet?
No, it is not recommended to replace an RV toilet with a regular toilet. RV toilets are designed differently, to operate in a smaller space, and to operate on a low water pressure. Because of this, the tanks and hardware on an RV toilet are specially designed to function in this space.
Installing a regular toilet in an RV would require you to make significant changes to the room and water system, which could be very costly and may not even be possible. Additionally, a regular toilet would use a much higher water pressure than what is necessary for an RV toilet, causing the RV’s water system to frequently be drained.
Ultimately, it is best to keep the RV toilet as-is and adjust other aspects of the RV bathroom to suit your needs.
Can one person lift a toilet?
Yes, one person can lift a toilet, but it is generally not a recommended task. Toilets can be heavy and difficult to maneuver, especially if they contain the water tank, and they can be dangerous if they are not handled correctly.
Lifting the toilet out of the floor may also damage certain pieces of the bathroom, like the flooring, so it is best to have more than one person do it. If you only have one person, it is recommended to use equipment like dollies and straps to ensure that the task is completed safely.
Additionally, it is important to turn off the water supply and properly unplug the toilet before attempting to lift it.
What’s the labor cost to remove a toilet?
The labor cost to remove a toilet will depend on a number of factors, including the type of toilet, the location, and the scope of the job. The cost of labor will also vary depending on the contractor’s experience, the complexity of the job, the availability of materials and tools, and the amount of time required to complete the job.
Generally speaking, the labor cost to remove a toilet can range from $75 to $200, depending on the factors mentioned above. Removal of the toilet will include turning off the water supply, disconnecting any plumbing fixtures, unscrewing and removing the toilet, and disposing of the old toilet.
In some cases, patching may be required to repair any damages made to the floor during the removal process.
How much does it cost to remove and install a new toilet?
The cost of removing and installing a new toilet will depend on several factors, including the type of toilet, the complexity of the job, labor costs and supplies. On average, the cost can range anywhere from as little as $200 to as much as $800 or more.
The cost may even be higher if additional plumbing work is needed or if additional materials, such as a new wax ring, must be purchased. It’s also important to note that some plumbers may charge a flat rate for the job rather than an hourly rate.
Additionally, some plumbers may not charge a flat rate, but may have a minimum fee that must be paid regardless of the time spent.
In general, the cost to remove and install a toilet could include the following:
-Labor costs: Depending on how complex the job is, labor costs can range anywhere from $140 to $550 or more.
-Materials: Toilet costs vary greatly, but can range anywhere from $60 to $400 or more, depending on the quality and features.
-Other materials: Depending on the type of installation, you may also need to purchase a new wax ring for the base of the toilet, which generally costs around $10. You may also need to purchase mounting bolts and other related supplies, which could cost an additional $20 to $50.
-Permits: Depending on your local jurisdiction, you may also have to pay a fee for a plumbing permit, which could cost around $60.
Overall, the cost of removing and installing a toilet could be as little as $200, or could range as high as $800 or more.
Do you need planning permission to remove a toilet?
In most cases, you will not need planning permission to remove a toilet from your home. However, there are certain conditions you need to meet in order for it to be considered legal.
First, the toilet needs to be in a single-family residence and it can’t be the only toilet in the house. You also need to make sure that the structural integrity of the home is not affected when the toilet is removed.
This means that you will have to assess the plumbing system and make sure that it is in good condition before you can begin to remove the toilet.
You will also have to make sure that everything is up to code and that you are following all of the relevant building regulations. As well, once the toilet has been removed, you will need to prepare to properly remove the waste and make sure that it doesn’t present a public health hazard.
In addition, if the toilet you are removing is an integral part of the bathroom, such as if it is attached to the wall or if it is a part of a suite, you might need to contact your local building control officer to confirm whether or not you will need specific planning permission.
Overall, most homeowners won’t need planning permission for removing a toilet, but it is always best to check before starting any home renovation project.
How long does it take to take an old toilet out and put a new one in?
The amount of time it takes to remove and replace an old toilet with a new one may vary based on several factors, such as the type of toilet, how it was originally installed, and any complications that may arise.
If a standard “two-piece” toilet (with a separate tank and bowl) was installed in accordance with standard industry practices, it shouldn’t take more than 2-3 hours to remove it, dispose of the old one and install the new one.
If the new toilet is of the same type and style, the installation may be quicker.
If the job involves retrofitting a new toilet onto existing plumbing, or if the toilet being replaced is a “one-piece” (tank and bowl are connected into one unit), then the process may take longer. This is because it will require additional preparation and installation steps, such as plugging the drain or making plumbing connections to the existing waste line.
No matter how long the job is expected to take, it’s always a good idea to factor in an additional half hour or so in case of unanticipated surprises. The new toilet should be securely and safely installed, so it’s important to take the time to make sure everything is done right.
How do you empty the water before removing the toilet?
To empty the water before removing the toilet, you will need to shut off the water that supplies the toilet by turning off the shut-off valve. This should be located behind the toilet or on the wall near the toilet.
Once the water has been shut off, flush the toilet a few times to drain most of the water out of the tank and bowl. You can then use a sponge, bucket, or old towel to soak up and remove any remaining water in the bowl.
If a large amount of water remains and won’t drain, you can use a wet/dry vacuum to remove it. Once all of the water has been emptied, you can begin to remove the toilet.
What size wrench do I need to remove a toilet?
The size wrench you need to remove a toilet depends on the brand, model, and style of toilet. Generally, a 7/16-inch wrench or adjustable wrench is all that is needed to remove the bolts, which attach the toilet to the floor.
However, some newer toilets may require a larger wrench size, such as a 1/2 inch or even a 9/16 inch. Be sure to double check the size of your washer and bolts before selecting your wrench. If in doubt, bring the toilet to your local hardware store for assistance in determining the correct size wrench for your specific toilet model.
Can you put a regular residential toilet in an RV?
Yes, you can put a traditional residential toilet in an RV. The process will require some modifications to the bathroom area of the RV and potentially some plumbing changes as well. The plumbing and installation processes will differ depending on the type of toilet you choose to install.
Working with a plumber or a professional who has experience installing toilets in RVs can help make sure the process is done correctly and in accordance with local plumbing laws and regulations. Generally speaking, an RV toilet will require special venting that may need to be installed in order to comply with codes.
Additionally, you will need to make sure the RV’s water supply and waste system can support the new toilet. Choosing a toilet that is designed for use in RVs may also help make the installation process easier.
How do I know what model RV toilet I have?
In order to know what model RV toilet you have, you will need to first locate the model number located on the toilet itself. The model number is typically located on either the underside of the seat or written on a label on the outside of the toilet.
If it is not written directly on the toilet itself, you can also look for identifying information on the manual or packaging that came with the toilet. Once you have the model number, you can use it to research your specific toilet model and find out the exact make and model of the toilet.
What type of toilet does an RV use?
An RV typically has a type of toilet known as a “cassette” toilet. This is a special toilet that requires no direct plumbing connection. Instead, a removable cassette is filled with water and waste and then removed and emptied at a designated RV dump station.
Cassette toilets are generally small, efficient and easy to maintain, allowing for convenient sanitation in an RV. They generally feature a foot pedal for flushing, a small tank for freshwater, and a small waste tank that must be emptied frequently.
Where is the model number on toilet located?
The model number on a toilet can usually be found on a label on the back of the toilet near the floor. It may also be located on the side of the tank, depending on the make and model of toilet. On some older toilet models, it may even be printed on the underside of the tank lid.
If the label is not visible, you can remove the tank lid to check underneath. Additionally, the model number may be found in the owner’s manual that comes with the toilet, or on the manufacturer’s website.