Flip-it tub stoppers are designed to be easily replaced, so removing them is relatively simple. To detach the stopper, first turn the stopper counter clockwise until it is loose. Then, using your hands, grasp both sides of the stopper and remove it from the drain.
You may need to use a little force, as the stopper may be stuck. Once the stopper is detached, use a flathead screwdriver to pry off the clip from the tailpiece. The clip helps secure the stopper in place and is often held on with plumber’s tape.
After the clip is removed, the flip-it tub stopper can be removed. Installation of a new stopper is the reverse of the removal process.
What are the different types of bathtub drain stoppers?
The most popular types of bathtub drain stoppers are the lift-and-turn drain stopper, the push-and-plug drain stopper, and the trip lever drain stopper.
The lift-and-turn drain stopper is a simple, easy-to-use stopper that can be lifted and turned to open and close the drain. It is generally easy to install and comes in many different colors and finishes.
The push-and-plug drain stopper is a more user-friendly option for those who prefer a push-style stopper. It can be pushed in to close the drain and pulled out to open the drain.
The trip lever drain stopper is more of an advanced drain stopper that is typically less common. It features a lever on the outside of the bathtub that is used to open and close the drain. It is more difficult to install than other types of drain stoppers, but it adds an extra element of style and convenience to any bathroom.
In addition to these popular types of bathtub drain stoppers, you can also choose from specialty stoppers like the suction cup or suction-and-toggle drain stopper. These are designed to be particularly effective at sealing and unblocking bathtubs.
No matter what type of bathtub drain stopper you choose, make sure that it is properly installed and maintained to ensure a long and lasting seal.
How do you remove a bathtub drain without special tool?
Removing a bathtub drain without a special tool is not impossible, although it will depend on the type of drain you have. If your bathtub has a toe-tap style drain, carefully pry open the stopper assembly to remove it.
There should be a small access hole that the pry bar can fit into and help you to remove the stopper. If your bathtub has a lift-and-turn style, start by turning the knob clockwise until it no longer turns.
Then, you will need to get a screwdriver or a flat head pry bar and insert it into the drain hole to loosen the stopper. Once you’ve done this, you can reach down inside the drain and pull out the stopper assembly.
If your bathtub has a trip-lever style, you will need to remove the faceplate first. This can be done by unscrewing it from the wall. Next, use a screwdriver to loosen the screw that attaches the cable to the trip lever.
Finally, lift the lever up and take out the stopper. Once you have removed the stopper, you may then need to use a pair of pliers to remove the nut from the drain assembly. This will allow you to pull the entire assembly out of the bathtub.
How do I remove the pop up stopper assembly?
Removing the pop up stopper assembly from your sink is a fairly simple process. The first step is to turn off the water supply to the sink. Then, use a pair of pliers to unscrew the nut holding the lift rod to the top of the overflow plate.
Carefully remove the lift rod and the overflow plate together. Once the plate and rod are removed, use a screwdriver to remove the screws holding the assembly to the sink drain. After all screws are removed, the entire stopper assembly can be carefully pulled out.
If the assembly is stuck and won’t come out, use a pair of channel locks will to unscrew and remove any bolts holding the assembly together. Once the pop up stopper is removed, the new replacement can be installed in the same way.
Can you remove the bathtub drain stopper?
Yes, it is possible to remove a bathtub drain stopper. To do this, first you will need to unscrew the stopper from the body of the drain. In most cases, you will be able to turn the stopper counter-clockwise to unscrew the stopper from the drain, however some stoppers may require a screwdriver to move.
After unscrewing the stopper, you may need to remove the rubber gasket, which will be held in place by one or two screws. Once the gasket has been unscrewed and removed, you will be able to lift the stopper out of the drain.
If the stopper is very difficult to remove, try using a pair of pliers or a wrench. If the pliers or wrench don’t work, you may want to consider replacing the stopper, as it may be too worn out to properly fit in the drain.
How do you retrieve a tub drain trip that fell off the linkage?
If you have a tub drain trip that has fallen off the linkage, you will need to retrieve it. To do this, you will need to begin by draining the tub. To avoid flooding, you can move the overflow lever to the downward position before you begin draining the tub.
Once you have done this, remove the screws on the drain cover and take it off to expose the drain.
Once the drain is exposed, reach into the drain to find the trip lever. It should be located either at the top or the bottom of the drain and can be reached within the drain’s opening. If you need to reach further in, you will need to use a pair of long-nose pliers.
Gently grasp the trip lever with the pliers and carefully remove it from the drain.
Once you have successfully removed the trip lever, you will need to reattach it to the linkage. Check to see that the linkage is in good condition, then slowly lower the trip lever into the linkage until it locks in place.
Finally, return the drain cover and secure it with the screws. You should now be able to lift the lever up and down to open and close the drain.
Are bathtub drain stoppers universal?
No, bathtub drain stoppers are not universal. There are a variety of different stopper designs that can be used in bathtubs, and each one is specific to the type of drain and the particular tub. Pop-up stoppers are the most popular, and they usually require a matching lift rod and linkage that needs to match the tub size and type.
Toe-push stoppers, on the other hand, have rounded edges at the base that indicate the correct type of stopper for the tub. Finally, the trip lever stopper is mounted inside the tub and requires a compatible trip lever mechanism on the outside of the tub to operate.
Sizing is also important, as some older tubs used non-standard sizes, so measuring thoroughly is important when selecting a replacement stopper.
What size bathtub drain stopper do I need?
The size of bathtub drain stopper you need will depend upon the type of bathtub you have. There are three main types of bathtub drains – a standard drain, a deep soak drain, and a voyageur soak drain.
Standard drains often use a trip lever drain stopper, which can be purchased in a variety of sizes. The majority of trip lever drains are 7 5/8 inches long and fit the standard drain size, which is 1 7/8 inches.
For a deep soak drain, the standard length may not be long enough – in this case, you’ll need to purchase a 10 inch trip lever stopper. Voyageur soaks, meanwhile, require a 12 inch long drain stopper.
Be sure to measure your drain correctly to ensure you purchase the right size stopper.
What can I use instead of a tub stopper?
If you’re looking for an alternative to a tub stopper, there are a few options to choose from. The simplest of these is a plug or drain cover. These plugs and drain covers generally come with a pair of handles or an easy-to-use knob that makes them easier to lift out when needed.
Some have built-in suction cups or suction cups that need to be attached to the bottom of the tub. These suction cups help to keep the plug in place while in use and make it easier to retrieve the plug when needed.
Another option is to use a drain basket or strainer. These are designed to fit into the drain of the tub and catch hair, soap residue, and other debris before it can make its way down the drain and cause a clog.
This is an especially useful solution if you live in an area with hard water, as these baskets can help to catch limescale and other minerals before they can build up in the drainpipe and cause a blockage.
Finally, you could opt for an overflow drain cover. This is a circular cover that fits over the drainpipe itself and provides an additional barrier to stop water from filling the tub to an excessive level.
Not only can this help provide peace of mind, but it can also add a decorative element to your bathroom as there are many styles and design options to choose from.
How much does it cost to replace a stopper in the bathtub?
The cost to replace a stopper in the bathtub depends on the type and style of bathtub stopper, as well as the cost of labor. Basic, generic bathtub stoppers typically cost between $5 – $20, while more decorative and specialty drain stoppers can cost up to $100 or more.
On top of that, the cost of labor to install the new drain stopper can range from $50 – $150, though the cost may be higher depending on the difficulty of the installation. Therefore, on average, replacing a bathtub drain stopper can cost anywhere from $55 – $170, with the more expensive end of the spectrum usually attributed to specialty bathtub stoppers.
Are bath plug holes a standard size?
No, bath plug holes are not a standard size. The size of a bath plug hole will be determined by the size of the bath, as well as the type of bath. For example, a large freestanding bath may have a larger bath plug hole as compared to a small built-in shower.
The bath plug hole size also depends on the manufacturer, as different brands and models may have different sizing. To make sure you get the correct size bath plug hole, it’s best to measure the hole before buying the plug.
How do you measure a bath plug?
Measuring a bath plug is fairly straightforward, although it is not something that you likely do on a regular basis. Firstly, you will need a measuring tape or ruler that is long enough to span the widest point of the bath plug.
To measure the plug, place the measuring tape on the top surface of the plug, at the point where it meets the bath. Make sure that the tape is flush against the surface, and hold it firmly in place. You then need to measure the length of the plug, taking into account the depth of the plug bowl and the length of the plug stem, which will give you the total width of the plug.
You can then use this measurement to find a suitable replacement plug or drain.
What is the standard bathtub stopper size?
The standard size for bathtub stoppers is 1. 25 inches in diameter. This standard size is typically for any pop-up or lift-and-turn style bathtub stoppers. It is possible to find “universal fit” stoppers that can be adjusted to different sizes and configurations, but the standard size is the 1.
25 inch diameter. This size should work for the majority of bathtubs and the installation process for these types of stoppers is typically straightforward. Additionally, the larger size allows for a more secure seal, meaning that when the stopper is in the closed position, it will effectively stop the flow of water.
How do I know what size bath plug I need?
When determining what size bath plug you need, you should first measure the size of the bath drain hole. Use a ruler or a measuring tape and measure out the diameter of the bath drain hole. Make sure you measure from edge to edge and not from center to center.
Once you have the diameter, you will know what size bath plug you need. Most bath plugs come in standard sizes, such as small (1 to 1 1/4 inches), medium (1 1/4 to 1 1/2 inches), or large (1 1/2 to 2 inches).
If your measurements do not match any of the standard sizes, you may need to use an adjustable bath plug or a rubber stopper to fit the drain hole.
Can a tub stopper be replaced?
Yes, a tub stopper can be replaced. Replacing a tub stopper can be a relatively easy process and will vary depending on the type of tub stopper you have. If you have a pop-up or lift-and-turn stopper, the process is relatively straightforward and involves removing the stopper from the drain, cleaning the area around the drain, inserting the new stopper, and using a putty knife to secure it in place.
If you have a trip-lever stopper, you will also need to remove the lever mechanism from the overflow plate. To do this, you will need to detach the cover plate from the wall, unscrew the screws on the trip lever, and detach the link arm.
Once you have the new stopper, you can install it by attaching the new lever mechanism, attaching the cover plate, and testing for a watertight seal. It is important to keep the tub clean and free of debris before installing the new stopper to ensure a good fit.