Installing a push down drain from Moen is an easy and straightforward process, that shouldn’t take more than an hour.
You will need a few materials in order to begin:
-Moentrol Tub Valves
-Drain trim kit
-Putty knife
-Plumber’s tape
-Silicone adhesive
Step 1: Install the Tub Valves: Start by locating the wall of the tub and the studs that hold the tub in place. Make sure to mark the studs and measure where the valve should be mounted. Now take the MoenTrol valves and install it using the included screws, making sure to mount it securely.
Step 2: Install the Drain Trim:Once the valves have been installed, it is time to install the drain trim kit. Begin by placing the drain trim into the designated mounting hole, and secure it with the provided screws.
Step 3: Connect the Drain Trim to the Valves:Once the drain trim has been installed, you can now use the putty knife to scrape away any debris that may have gotten into the mounting hole. Then make sure to seal any joint with the plumber’s tape.
Finally, use the silicone adhesive to attach the drain trim to the valves.
Step 4: Test the Installation: After all the connections have been made to the valves and the drain trim, it is important to test the installation. You should fill the tub with a few inches of water, and examine the drains for any possible leakage.
Make sure that the water is draining properly and replace any necessary parts if need be.
Once you have completed these steps, your Moen push down drain will be successfully installed and you can begin to enjoy your tub.
How do you remove a Moen push down drain?
Removing a Moen push down drain is a rather simple process. To start, ensure that all water has been completely drained from the sink. Next, loosen the ring on the bottom of the drain by using a flathead screwdriver or similar tool.
Once the ring has been loosened, you should be able to pull it up and off the sink. After this, you should be able to remove the drain pipe as well. Finally, simply pull the Moen push down drain out of the sink and it should be free.
When you’re finished, your new drain should fit right into the spot vacated by the old one.
How does a push button drain work?
A push button drain is a kitchen sink or bathroom sink drain setup that is activated by pushing a button or pressing a lever. This type of drain utilizes a pop-up assembly, which is a mechanism that opens and closes the drain through the use of a stopper that is operated by a lever or button.
When you push a button or pull the lever, the stopper is raised, and the water begins to drain. This is achieved through use of a pull-chain or a plunger/cam assembly located either above or below the sink.
The pull-chain is connected to the plunger which, in turn, is connected to the stopper. When the plunger is pulled, it lifts the stopper, allowing the water to pour out. To keep the water from overflowing down the sink, a tension-type anti-siphon assembly is used, which prevents air from entering the system.
The advantage of push button drains is their aesthetic appeal. They are hidden from view, making them a popular choice for modern bathrooms and kitchen sinks. Additionally, these drains are designed for easy installation, being simple to install and replace for the average consumer.
How do push down plugs work?
Push down plugs are a type of electrical safety device that are designed to shut off power to a circuit if it senses a power surge or if the current gets too high. The device works by using a spring-loaded metal plate that sits inside the plug.
The plate is connected to a pair of metal contacts. When the current passing through the contacts is too high, the plate is forced down, thus breaking the connection between the contacts and shutting off the power to the circuit.
In effect, the plug acts as a safety valve that prevents dangerous levels of current from passing through the circuit. This type of device is commonly used in electrical outlets in homes or businesses to prevent overheating and possible fires from occurring due to high current passing through the outlet.
Do pop up drains need plumbers putty?
Yes, pop up drains typically require the use of plumbers putty. Plumbers putty is a type of waterproof sealant which is specifically designed to form watertight seals around fixtures such as drains, faucets, and pipes.
Because pop up drains are used in wet areas, it is important to ensure that they are watertight. Plumbers putty can be used in the drain installation process to ensure a tight seal. Plumbers putty is applied around the drain, and pushed into any gaps or crevices.
This will provide an airtight seal to keep water from leaking through the drain. If the plumbers putty is properly installed, it should last for years without needing replacement. Additionally, plumbers putty is an economical material which makes it an effective choice for sealing pop up drains.
Do you need plumbers putty to install a sink drain?
Yes, plumbers putty is a necessary component when installing a sink drain. Plumbers putty is a malleable material that creates a waterproof seal around a sink drain, helping to keep out dirt, water, and other contaminants.
It works by forming a tight seal when two surfaces are compressed, so that liquids and gases cannot leak through the surrounding pipe. Plumbers putty can be purchased from most hardware stores, and installation instructions usually come with the product.
When installing a sink drain, the plumbers putty should be applied around the drain flange before tightening the bolts and attaching the strainer body to the drain flange. After the sink drain is installed, the plumbers putty should be left for about 24 hours so it can dry and solidify, to ensure that a watertight and durable seal is formed.
Is it better to use plumbers putty or silicone?
It really depends on the situation. Plumbers putty is a putty-like material typically used for sealing joints in plumbing fixtures, whereas silicone is a more flexible, rubber-like sealant. Each has its own pros and cons which should be taken into account when making a decision on which one to use.
Plumbers putty is generally considered a better choice for between metal joints or for use on a single surface. It tends to form a solid seal and won’t shrink or crack over time. It also doesn’t corrode, discolor, or stain, making it a good choice for use on fragile surfaces like porcelain.
The downside to plumbers putty is that it has limited flexibility, so it’s not suitable for use on surfaces that may shift or move.
Silicone is more flexible than plumbers putty and is a better choice for large surfaces, surfaces that move or shift, or for use with plastic or vinyl materials. It also adheres better than plumbers putty and won’t break down in the presence of oil or moisture.
Additionally, silicone can be applied to wet surfaces and won’t stain or corrode. The downside to silicone is that it can be difficult to remove later, so if you anticipate needing to do repairs in the future then plumbers putty might be a better choice.
Ultimately, the choice between plumbers putty and silicone should be based on the specific application being used. Understanding the pros and cons of each and taking into account the movement and material of the surfaces to be sealed will help you make the right choice.
How long should plumbers putty sit before use?
Plumbers putty should sit for at least 3 hours before use. It is important to allow the putty to dry and cure on its own before it is applied. The drying and curing process is what helps the putty to adhere securely to the surface and prevent any leakage.
It’s best to avoid making tight contact between the putty and its surface until the curing process has been completed. Applying the putty before it’s completely dried may compromise the seal, so it’s important to plan accordingly and allow the right amount of time for the putty to cure.
Where should a pop up drain be placed?
A pop up drain should be placed in the lowest spot of the sink or bathtub it is being installed in. This ensures that the water flowing in goes down the drain and that no water will accumulate in the basin.
Additionally, the pop up drain needs to be aligned so that the drain pipe points downward. If the tub or sink is installed in a floor with a slight incline, it is best to point the upper end of the drain pipe slightly downward towards the drain.
To ensure the pop up drain is secured properly, you should use caulk or silicone to attach the drain to the sink.
Should I use plumbers putty or silicone on tub drain?
The answer as to whether you should use plumbers putty or silicone when installing a tub drain really depends on the specific installation. Generally speaking, plumbers putty should be used when installing a stopper or trip lever, while silicone should be used below the drain flange.
Plumbers putty is a soft, moldable material that is used to create watertight seals around fixtures like drains and other fittings. The putty should be placed directly between the tub surface and the drain flange before it is tightened into place.
Silicone is a bit more versatile and can be used around the entire drain to provide additional water resistance and also a bit more protection from leaks. However, it is important to note that silicone can discolor some surfaces (such as marble or enamel) and should only be used when it is not visible.
It’s important to carefully read all of the instructions included with your tub or drain before beginning the installation to make sure you are using the correct material for that particular installation.
Are pop up drains a good idea?
Pop up drains can be a great choice for certain situations, as they are less expensive than traditional drains and can also provide a stylish and contemporary look depending on the specific grade of materials used.
Additionally, as a single-piece construction, they are fast and easy to install, which is convenient for many people.
However, pop up drains are more prone to leaking and blockages, as their design is more complex. Additionally, depending on the grade and model, they may not be able to handle large amounts of water.
Furthermore, they don’t always match the aesthetic of certain sinks, tubs, and showers, so they may not be the best choice in some cases.
Overall, the decision to use a pop up drain will ultimately depend on your budget and specific needs. If used in the right situation, they can be a great choice for anyone looking for an affordable and easy to install solution.
Why is my pop-up plug not working?
If you’re sure you have the right settings and the plug is plugged in correctly, then the problem may be with the plug itself. A common cause of this type of problem is a defective outlet or wiring. You may want to start by testing the outlet with a voltage meter.
If the outlet is working correctly, you should then check the wiring. Make sure the plug is connected to the correct wires and that all of the wires are snug. If they are loose or if the insulation is frayed, it could be preventing the plug from working.
If you’re still having trouble, you may have to replace the plug entirely.
How do you reattach a pop-up stopper?
Reattaching a pop-up stopper typically involves loosening and removing the existing drain assembly from the sink, installing a new & improved flange, and connecting it to the existing pop-up rod.
First, you will want to locate the stopper assembly beneath the sink. If you cannot spot the stopper, a flashlight may be necessary to assist in finding the right area to start.
Once you have located the drain assembly, you will now need to remove the existing drain. To do this, begin by using a wrench or socket to carefully unscrew and remove the flange and tailpiece from the drain.
The tailpiece is the horizontal pipe connected to the stopper, and the flange is the part with the threads that you unscrew from the sink.
Next, you will want to install your new flange. This should provide you with a more secure, better-fitting drain assembly for your pop-up stopper and will make the process faster and easier than struggling with the existing assembly.
When screwing the new flange onto the sink, be sure to use additional plumbers putty underneath to create a water tight seal.
Finally, connect the pop-up stopper rod to the flange and attach the new tailpiece and stopper. Then, remount the overflow plate or collar to the beveled edge and you are finished with the reattaching of your pop-up stopper!.
How do you fix Popgrip?
If you are having issues with your Popgrip (such as not sticking properly or being too tight/loose) then there are a few methods you can use to fix it.
First, try to clean the Popgrip and the back of your phone. Anything that is preventing the grip adhering properly to the phone needs to be removed. Use a lint roller, a soft cloth, or a Q-tip dipped in rubbing alcohol to lift dirt and residue from both surfaces.
Another method is to use an extra adhesive such as a foam adhesive pad or double sided adhesive film. Peel the backing off of these pads and stick it to the back of the Popgrip. This will give it an extra level of adhesion.
You may want to use a few pads if your Popgrip is particularly loose or is sliding around on the phone.
Finally, if the Popgrip is too tight on the phone, you can try to stretch the ring slightly by pulling it away from the grip and rotating the ring back and forth. It might take a few tries before you get the desired tension.
If none of these methods work, then it is likely time to replace the Popgrip.
How do you change the slide on PopGrip?
Changing the slide on a PopGrip is quite easy. Start by ensuring that the bottom of the PopGrip is facing you. Locate the small latch on the tapered edge of the PopGrip cup. Use your finger and thumb to ‘pinch’ the latch, which will allow you to slide the PopGrip cup off the base.
This will expose the slide that fits snugly into the PopGrip cup. Take the new slide and slide it onto the base of the PopGrip. Once it is located in the slot, use your fingers to secure the latch. Finally, take the PopGrip cup and slide it back over the base, with the latch facing up.
This will secure the slide into the cup and the PopGrip will be ready to use.