Removing a toilet seat is actually quite a simple job that anyone can do. All you need is a screwdriver, either a Philips or flat head.
Start by lifting off the lid and carefully removing any decorative caps, plastic washers, and metal washers. Once these are removed, locate the mounting screws that hold down the seat and use the screwdriver to carefully remove them.
The seat should then come off easily. If the screws are stuck on, you may need to spray them with some oil or WD-40, but this is not always necessary. Be sure to keep the screws in a safe, accessible place, as you will need them for re-installing the seat later.
Once the seat is removed, you can use an old towel to wipe away any gunk or buildup around the base of the toilet and the chrome area. Once this is done, you’re ready to install your new seat. To do so, simply reverse the steps, lining up the mounting screws on the seat and using the screwdriver to tighten them down.
Finally, put all of the plastic and metal washers back on in the same order they were taken off and your toilet seat installation is complete!.
How do you take the seat off a toilet?
In order to remove the seat from a toilet, you typically need to unscrew the nuts that are connecting the seat and lid to the toilet. They are usually located either at the back of the toilet at the center or on the sides of the seat near the hinges.
Use a pair of pliers to hold the nuts in place and unscrew them using a screwdriver. If the nuts are too tight, use a wrench for leverage. Once you have removed the nuts, set them aside so that you don’t lose them when you take the seat off.
You can then lift the seat and lid off of the toilet. If there are any gaskets or washers remaining, remove them as well.
Why can’t I unscrew my toilet seat?
If you are having difficulty unscrewing your toilet seat, there are a few potential causes.
The most common is that the plastic nuts that secure the seat to the toilet bowl have been over-tightened in the past, making them difficult to loosen by hand. In these cases you may need to use an adjustable wrench to loosen the nuts and unscrew the toilet seat.
Another possibility is that the plastic nuts have fused to the toilet bowl over time, making the seat impossible to unscrew. In this case, you may need to replace the toilet seat entirely.
It is also possible that the fastening screws have rusted in place, making them impossible to remove. If this is the case, you may need to use penetrating oil to lubricate the screws, giving them a chance to break free.
Finally, the toilet seat may be a “permanent mount” style—these are designed to stay in place, so they do not feature removable screws. If you have this type of seat, there is no way to unscrew the seat from the toilet bowl.
How do you unlock a toilet seat and remove it?
In order to unlock and remove a toilet seat, typically what you will need to do is locate the bolts on the underside of the toilet seat. Depending on the model or style of seat that you have, the bolts may be plastic fittings or metal nut and bolt type.
Once you locate the fasteners, use a socket wrench to remove the nuts or plastic fittings that are holding the seat in place. You may need to hold onto the bolts to keep the seat from moving around as the nuts are loosened.
Next, pull the seat away from the toilet and when it is fully off, set it aside so that you can replace it with a new one.
What tool do you need to take a toilet seat off?
To take a toilet seat off, you will need a few tools. Depending on the type of seat you are removing, you may need a flathead screwdriver, a Phillips head screwdriver, a socket wrench, and a putty knife.
If you have an old-style seat secured with screws, use the screwdriver to unscrew the nuts that hold the seat in place. If the seat is secured with plastic locking nuts, use the socket wrench to loosen the nut and the putty knife to pry off the seat.
Be sure to keep track of the hardware and nut size you remove, as you may need them again when installing the new seat.
What are the different types of toilet seat fittings?
There are four main types of toilet seat fittings: top fix, bottom fix, back to wall, and stand-alone. Top fix toilet seats are the most popular, and are typically found with a plastic hinge and push button that is connected to the cistern or wall, and holds the seat firmly in place.
Bottom fix fitting toilet seats attach to the underside of the pan with a clip and require the toilet to be raised off the floor. Back-to-wall toilets require an enclosed space so the seat attaches to a hole in the wall and is back-lit with a concealed cistern concealed behind the wall, whilst stand-alone toilet seats have no cistern attached and have to be used in a wall-less space.
How do I know what type of toilet seat I have?
To determine what type of toilet seat you have, first carefully examine the hinge area of your toilet seat. If the hinges are visible, with no bar connecting them, then you have a standard toilet seat.
If there is a bar connecting the two hinges, then you have a round or elongated toilet seat. To determine which one you have, measure the distance from the front of the seat to the back. If the distance is approximately 17 inches, then your toilet seat is round.
If the distance is greater than 17 inches, then it is an elongated toilet seat.
Do all toilet seats have the same fixings?
No, not all toilet seats have the same fixings. Depending on your make, model and size of the toilet. Generally, the four main types of toilet seat fixings are top-fixed, bottom-fixed, side-fixed and clip-on varieties.
With top-fixed and bottom-fixed models, you will typically find a long plastic screw at the back of the toilet seat which is used to attach it to the toilet itself. You can access this screw by lifting or removing the toilet seat first.
Side-fixed toilet seats are attached with two screws at the sides of the seat, meaning you don’t need to lift the toilet seat in order to access them. Clip-on toilet seats are the easiest to install, as simply clip onto the toilet with no tools required.
With all these varieties it is important to remember that the toilet seat needs to be the correct size and shape for the toilet, otherwise it won’t fit and could cause the toilet to become unstable.
Are all toilet seats standard fitting?
No, not all toilet seats are standard fitting. Toilet seats come in a variety of shapes and sizes, so not all of them are the same. The most common toilet seat size is usually a 4-bolt design, which has 4 mounting holes to attach the seat to the toilet bowl.
Other non-standard sizes could be needed for round, elongated or larger toilet bowls. The best way to make sure your toilet seat will fit is by measuring the distance between the holes where the seat attaches.
You can usually find the measuremnt specifications on the packaging of the seat you purchase, or you can measure the existing toilet seat you’re replacing. You should also consider whether or not you need a slow-close or quick-release toilet seat.
How do you lift a toilet seat without touching it?
One of the best ways to lift a toilet seat without touching it is to use a toilet seat lifting device. These devices are typically made of plastic or metal and feature a handle on top for easy lifting.
They work by providing leverage, so you don’t need to physically touch the toilet seat when you lift it. Before using it, attach the device to the sides of the seat. When you’re ready to lift the seat, simply grab the handle and raise it.
Be sure to follow any specific instructions included with the product you have. For extra hygiene, it’s also a good idea to use a disinfectant spray on the handle of the device and on the seat. This will help prevent any spread of germs.
How do you loosen a toilet lock nut?
To loosen a toilet lock nut, you’ll need a wrench to get underneath the nut and rotate it counterclockwise. It is helpful to lightly tap the wrench with a hammer if it’s difficult to break the nut loose.
Make sure to position the wrench in such a way that it gets a good purchase on the nut without damaging the porcelain. Once it’s loose enough, you can grab onto it and unscrew it by hand. If the nut is really stuck, you may need to use a bucket or some other object to give support to the wrench while you loosen the nut.
If all else fails, you can try applying a small amount of lubricant such as WD-40 to make it easier to loosen. Once the lock nut has been loosened, make sure to replace it with a new one.
What size wrench Do I need to remove a toilet seat?
The size wrench you need to remove a toilet seat will depend on the type of nuts and bolts used to secure the toilet seat. Most typical toilet seats are secured using a 3/8″ or 5/16″ nut and bolt combination, so you will need a corresponding wrench size to remove it.
Some toilet seats may be secured using a 7/16″ nut and bolt combination. It’s also important to note the type of head of the nut and bolt, as it may require a specific type of wrench or socket to loosen it.
If the nut and bolt is rounded, it may be easier to use an adjustable wrench or a ratcheting socket wrench. If the bolt head has a shape that requires a specific wrench, like star shaped or hexagonal, then you will need a corresponding wrench to remove the toilet seat.
If you’re not sure what size wrench to use, it’s best to check the manufacturer’s instructions for the toilet seat, or take a trip to your local hardware store or plumbing agent to purchase the appropriate wrench or socket.
Are all toilet seat fixings the same?
No, toilet seat fixings are not all the same. The most common fixing types are top fix, bottom fix and clip-on, but some toilets may require a specific type of fixing depending on the manufacturer or model design.
Top-fix toilet seats are attached to the pan by screws and plastic washers that fit through pre-drilled holes in the toilet. Bottom-fix toilet seats are secured to a bracket, or concealed hinge and clip-on toilet seats simply clip onto the surface of the pan.
Each of these types of fittings have pros and cons, so it is important to identify the correct type for the toilet and seat being installed to ensure a secure and comfortable fit.
What is P type and S type toilet?
P type and S type toilets are two types of construction techniques used in the construction of toilets. The differences between the two types of toilets have to do with the location of the flange and other components.
A P type toilet is one where the flange, the metal pipe that connects the waste pipe to the toilet bowl, is located inside the floor. This type of toilet is usually found in bathrooms with a lower ceiling, as the flange is installed before the bathroom floor of the bathroom is laid.
In addition, the waste outlet of a P type toilet is raised higher off the floor than an S type toilet, making it ideal for bathrooms with limited space.
An S type toilet is one where the flange is located above the floor. A separate collar or flange is affixed over the waste outlet on the floor and extends up to the connected toilet bowl. This method is generally used in bathrooms with higher ceilings as the flange is installed after the floor has been laid.
In addition, the waste outlet of an S type toilet is usually slightly lower than that of a P type toilet, making it more ideal for taller people.
Overall, the key differences between a P type and S type toilet are the location of the flange and the height of the waste outlet. In addition, the location of the flange is also important to consider when determining which type of toilet is best suited for a certain type of bathroom layout.
How do I stop my toilet seat from moving sideways?
To prevent a toilet seat from moving sideways, there are several solutions you can try. The simplest form of prevention is to purchase a toilet seat stabilizer. This is a device that attaches to the existing toilet seat and will help to keep it from shifting.
Other solutions include adding rubber or foam pieces to the hinges of the seat and tightening them onto the bowl. You can even make DIY stabilizers out of a piece of cloth placed between the seat and the bowl.
Additionally, you can try adjusting the screws located around the hinge to make them fit tighter. Finally, consider replacing the seat with a new one that fits more securely.