No, you don’t typically put flooring down before toilet. In most cases, you will install the toilet before laying down the flooring. To begin, measure out the spot for the toilet and mark off the area for installation.
Then, take out the existing toilet, if needed, and lay down your flange in the right location. Once the flange is secured in place, you can then set the toilet onto the flange and secure it tightly with the included bolts.
After the toilet is securely installed, you can then measure and install the flooring of choice – keep in mind to leave a gap of at least 1/8 inch between the floor and bottom of toilet to allow room for expansion.
Finally, replace the toilet seat and you’re all set.
Should vinyl flooring go under toilet?
Yes, vinyl flooring should go all the way under the toilet, as it is important to ensure that the toilet is secure and stable. Additionally, having the flooring cover the entire area around the toilet helps to keep the area dry and free from any water damage that could occur if the toilet is not properly sealed.
When installing vinyl flooring, you should use a seam sealer and a moisture barrier to create a secure and watertight seal around the toilet. This will help keep the flooring from buckling or warping from water exposure.
Additionally, it is a good idea to lay down a piece of subfloor such as a cement board or plywood prior to installing the vinyl flooring. This will provide extra stability for the toilet and help prevent it from shifting.
How do you put a floor around a toilet?
To put a floor around a toilet, start by measuring the area directly around the base of the toilet, and purchasing tiles that are suitable for the space. Once you have the tiles and necessary underlayments and grout, lay down a sheet of plastic sheeting in the area that’s to be tiled, securing it with duct tape.
You can then spread out a layer of thin-set mortar and use a notched trowel to evenly spread the mortar across the subfloor. Make sure to leave about a 1/4-inch gap between each tile. Line the edges of the tiles with tile spacers to ensure a consistent grout spacing.
Allow the thin-set to dry and cure according to the instructions. Once it’s ready, spread a layer of grout across the area, using a grout trowel, and using light strokes to move the grout into the lines along the edges of the tiles.
Use a damp grout sponge to wipe off any excess grout, and, when covered in a thin layer, leave it to dry and cure according to the instructions. Finally, once everything is dry, apply a sealer to the area to give it added protection, and allow the sealer to dry completely before using the space.
Does a toilet sit on top the tile?
No, a toilet typically does not sit on top of the tile. Toilets are usually mounted on the floor, with a wax ring placed between the toilet and the floor to provide a water-tight seal. Installing a toilet will usually require that an individual remove any tile or other flooring that may be in the way to be able to access the bathroom flooring.
Once the toilet is mounted, the tile or other flooring is secured around the toilet to create a finished look.
Is it better to tile under or around a toilet?
It is better to tile around a toilet because it is much easier to do, and it’s also better for the flooring beneath the toilet. When tiling underneath a toilet, a much more detailed installation process is needed, as the toilet must be properly sealed onto the floor and the edges must be caulked so the grout won’t crack.
Additionally, tiling around a toilet can give the toilet a more finished look and help create a much more seamless design in the bathroom. Lastly, it is much easier to access the underside of the toilet for cleaning or repairs if the installation has been done correctly when tiling around it.
What order do you install a bathroom?
When installing a bathroom, it is important to do the job in the right order of operations. First, you will want to prepare the bathroom by removing existing fixtures, breaking out any tile, and ripping out other existing elements.
Then, you’ll want to ensure you have all the necessary components of the new bathroom, such as the sink, toilet, shower, etc. Next, you’ll need to run all of the necessary plumbing including the main supply lines, drain lines, and all the hookups.
Finally, you can install the fixtures, tile, paint, and all the other details of the bathroom. Once everything is properly installed and secure, you can finish the job by connecting any remaining plumbing, hookups, and accessories.
Following these steps in the right order is the key to making sure your bathroom is finished correctly and looks beautiful for years to come.
Do you remove toilet when putting tile down?
No, it is not usually necessary to remove the toilet when laying tile around it. Doing so may cause extra damage and possibly plumbing problems, so it is typically best to work around it. The most important thing is to make sure that the new tiles have enough of an overhang below the toilet rim to cover the base of the toilet.
This usually requires placing the tiles around the toilet, rather than directly underneath it. Proper preparation is also essential when laying tile around a toilet. This includes removing the excess grout, wiping the area clean, and removing any debris.
Additionally, you should use sealant around the toilet base prior to laying the tile in order to ensure a secure fit.
What do you put around the base of a toilet?
When installing a toilet, it is important to surround the base with a rubber or foam sealant to help prevent water from leaking from the toilet. This can be done by affixing a toilet wax ring to the base of the toilet and then pressing the toilet into the floor.
The wax ring should be checked for damage prior to installation to ensure a tight and secure fit. Additionally, it is important to ensure that the floor is level and that all bolts are tightened securely before proceeding with the installation.
After the wax ring is correctly in place and the toilet is correctly installed, apply a bead of silicone caulk around the base of the toilet to ensure further protection against leaks. Make sure to thoroughly clean any excess caulk so that the area looks neat and tidy when finished.
What can you put between toilet and floor?
To ensure a proper seal, it is important to install a wax ring between the bottom of the toilet and the floor. The wax ring compensates for any irregularities in the floor and toilet, allowing a proper seal between the two.
In some cases, a foam gasket may also be used, or it can be used with a wax ring in the case of toilets installed on a concrete floor. Additionally, a toilet flange should also be installed, which connects the toilet to the waste pipe in the floor.
The flange should be sealed with plumber’s putty to ensure a tight seal before being screwed into the waste pipe.
How do I fill the gap between my toilet and floor?
Filling the gap between the toilet and the floor is an important step for keeping the restroom looking neat and clean, preventing large dirt and debris particles from collecting in the gap, and reducing the passage of odors.
Fortunately, this is a relatively easy process that can be done in a few simple steps.
First, you need to unscrew the bolt caps on either side of the toilet. Use a screwdriver to do this, and be sure to keep track of the bolt caps as you remove them. Then, remove the nuts and bolts, being careful not to damage the bowl or the floor.
Next, you will need to cut the wax ring to fit the gap between the toilet and the floor. Use a utility knife for this, and be sure to leave a thin gap between the toilet and the wax ring. This ensures a tight seal and prevents odors from entering the room.
Finally, install the wax ring and reattach the nuts and bolts. Make sure that everything is tight and secure, then replace the bolt caps. You should now have a snug seal between your toilet and the floor, which will keep your restroom looking neat and clean.
Can you overtighten toilet to floor?
Yes, it is possible to overtighten a toilet to the floor. While this is not an ideal situation, the process for securing the toilet to the floor is not difficult and can be done by anyone. To start, you will need the correct toilet floor bolts and a wrench.
After you’ve determined the correct location for the toilet, position the bolts and then use the wrench to tighten them to the floor. You will want to be careful not to overtighten them as doing so can cause the bolts to strip and pull out of the floor.
Additionally, over-tightening the toilet can cause the toilet bowl to break or crack. For this reason it is important to make sure you are only tightening the bolts until they are just snug, and not overwound.
If you are still having difficulty, you can always call a certified plumber to install your toilet correctly.
Do you put plumbers putty under toilet?
Yes, plumbers putty is typically used when installing a toilet. Plumbers putty should be applied to the toilet horn, the outlet at the bottom of the toilet, to form a watertight seal. Plumbers putty is a pliable, clay-like substance that is not made to dry or harden.
It can conform to various shapes and should be applied to the toilet horn and allowed to rest for a few minutes before the toilet is installed. After the toilet is installed, no putty should be visible and any excess should be wiped away.
It is important to keep the putty clean, as dirt and debris can reduce the effectiveness of the seal.
Do you install tile or toilet first?
Whether you decide to install the tile or toilet first is largely a matter of preference and convenience. If you plan to tile your bathroom, it is best to lay the tile before installing the toilet so that you can accommodate the toilet fitment width and its placement.
It also makes it easier to create a seamless connection between the edge of the toilet and the rest of the tile if you lay the tile first. Alternately, if you have already installed the toilet, tiling around it can be a bit of a challenge as you’ll need to make precise cuts to fit around the fitment.
When in doubt, consulting with a professional is a good idea, as they can give you advice based on the specific needs of your project.
Should I install toilet before or after tile?
It depends on the type of toilet you are installing, as well as the type of tile. Generally speaking, it is easier to install the toilet first before laying the tile. This is especially true when installing tile flooring, as the floor has to be prepped and level before laying tile.
Installing the toilet first gives you the opportunity to build and level the floor in the correct spot for the toilet. It is also easier to measure for the tile pattern before the toilet is installed.
On the other hand, installing a tiled wall first might make more sense if the room has other obstacles that would make it difficult to install the toilet before the tiles. In any case, it is always recommended that you consult a professional or a sales associate at the hardware store to determine the best course of action, especially if you are a beginner.
Should you remove toilet before tiling?
Yes, it is always recommended to remove the toilet before tiling. When tiling a bathroom, it is important to make sure that you have a solid, level foundation to work from, and removing the toilet beforehand gives you much better access to the subfloor.
Without having to work around the toilet, you can more accurately check the floor for any irregularities and fix them, such as bulges, ridges, and dips, before applying the tile adhesive and tiles. Additionally, it is much more difficult to ensure the toilet is sitting level, with the right gap between the base and subfloor, when the tile has already been laid.
Removing the toilet and then reinstalling it once the tiling job is finished will also result in a cleaner look and a better seal. Therefore, it is recommended that you remove the toilet before tiling.