Pairing your Jawbone Era with your Bluetooth-enabled device is a relatively simple process. To begin, turn on your Bluetooth-enabled device and open the device’s Bluetooth settings. Once in the settings, make sure the Bluetooth is turned on and visible to other Bluetooth-compatible devices.
Next, make sure that your Jawbone Era is powered on and not in sleep mode. You can wake it up by pressing the large button located on the side of the device. Once the Era is awake, the LED indicator light should turn green.
After both devices are powered on and can detect each other, locate the pairing button located on the side of the device. Press and hold the pairing button for a few seconds, or until the LED indicator light begins to flash red and green.
Your Bluetooth-enabled device should then detect the Jawbone Era, and display its name.
Once the device is detected, select the Jawbone Era from the list of devices to connect it to your Bluetooth-enabled device. Depending on the device, you may be asked to enter a pin code. If so, enter “0000”.
After a few moments, the LED indicator light should turn solid blue to confirm that the pairing was successful.
Your Jawbone Era is now paired and ready to be used. Enjoy!
How do I put Jawbone in pairing mode?
To put your Jawbone in pairing mode, you will need to press and hold the multi-function button (located on the outside of the Jawbone) for five seconds or until you hear the pairing tone. Once the Jawbone is in pairing mode, it will then be discoverable by any compatible device such as a phone, computer, etc.
Depending on the device, you may need to go into its Bluetooth settings and search for the Jawbone in order to complete the process. Additionally, some Jawbone models may need to be reset in order to be put into pairing mode.
To reset, press and hold the multi-function button for 15 seconds and then release. This can be done if the Jawbone does not enter pairing mode after following the five-second method.
Why is my Jawbone not connecting?
If your Jawbone device is not connecting, it could be due to a variety of causes including insufficient charging, an issue with Bluetooth, no access to data or a malfunctioning device.
First, check to see if the Jawbone is fully charged. If it has not been connected to a power source recently, the device may be running on too little power to reliably connect. Leave it connected to a charger for at least 30 minutes to check that it is operational.
Second, try connecting it to a different device or checking to make sure the Bluetooth on your device is turned on. Bluetooth connections often drop due to power outages or hardware failures, so restarting Bluetooth (or checking to make sure it is still running) can sometimes help.
Third, make sure you have access to data and that it is properly enabled. If you are using a cellular device to connect, double-check that you have enabled data. Similarly, if you are using a Wi-Fi connection, make sure that it is connected and working properly.
Finally, if none of these solutions work, it is possible that the Jawbone device itself may be malfunctioning. Contact the Jawbone support team to get help with the issue or ask them about a replacement device.
Is Jawbone still supported?
Yes, Jawbone is still supported. Although production of the fitness tracker has ceased, Jawbone offers customer support services to assist those who still have products that were purchased prior to discontinuation.
Additionally, there are online resources available to help users find replacement parts, troubleshoot problems with their device, and access firmware updates. The Jawbone Support website also provides step-by-step instructions on how to set up devices, conserve battery power, and transfer data from one device to another.
Finally, Jawbone provides a comprehensive FAQ page with common solutions to some of the most common questions about its products.
Can you turn up the volume on a Jawbone Bluetooth?
Yes, you can turn up the volume on a Jawbone Bluetooth. The way you do this will depend on the model of Jawbone Bluetooth you have. Generally, you can use the volume control buttons on the left side of the device to control the volume.
If you have the UP or UP4 model, also known as the Jawbone Prime or Jambox, you can use the dedicated volume up and down buttons on the left side of the device. Simply press and hold the + or – button until you reach the desired volume.
Alternatively, you can use the connected device’s controls such as a mobile phone to control the volume.
How do you factory reset your speaker?
If you’re looking to factory reset your speaker, the process will depend on the type of speaker you’re using.
For wireless/Bluetooth speakers, the process is relatively straightforward. Begin by disconnecting all cables or Bluetooth connections. Then, press and hold down the multifunction button – located on your speaker – for 10 seconds until you hear a voice prompt.
When completed, the speaker will have reset to its factory defaults.
For other types of speakers – such as sound bar speakers – you may need to consult the manufacturer’s instructions for details. Generally speaking, factory resetting a sound bar will involve pressing and holding down the ‘Power’ and ‘Select’ buttons until you hear a confirmation sound or prompt.
No matter what type of speaker you’re using, factory resetting it is generally an easy process if you have the right instructions.
Can a Bluetooth speaker be reset?
Yes, a Bluetooth speaker can be reset. Resetting your Bluetooth speaker can help resolve connection issues and other troubleshooting issues. To reset a Bluetooth speaker, the first step is to turn it off and then power it back on.
You should also disconnect the device from any other Bluetooth sources or networks. After it is powered back on, you should put it in pairing mode. The instructions for entering pairing mode vary across devices, so you should refer to manufacturer instructions.
Additionally, you can try resetting your device’s Bluetooth connection by removing it from your list of Bluetooth devices and re-adding it. If that doesn’t work, you can reset your entire device by using a pin, paperclip, or other small tool to press and hold the reset button for 10 to 30 seconds.
After the reset is complete, the device may need to reconnect to other connected devices before it is fully operational.
Where is pairing button Jambox?
The pairing button on the Jambox can be found on the right side of the device. It is a small, circular button with the Bluetooth symbol on it. When the Jambox is powered on, the pairing button will be lit blue and can be pressed to initiate the pairing process.
Depending on the model, you may need to press and hold the button for several seconds in order for the pairing mode to be enabled. Once the button is held down for long enough, the Jambox will enter pairing mode and the Bluetooth symbol will begin to pulse quickly.
At this point, the Jambox is ready to be paired with another Bluetooth device.