Putting a toilet back down depends on the make and model of the toilet, as well as the type of installation. Generally though, it involves making sure the toilet is properly seated on the mounting bolts before placing the tank back onto the bowl.
Make sure to line up the washers and nuts with the holes in the tank, then use your hands to gently push the tank down onto the toilet. Be careful not to use any tools that might damage the toilet’s surfaces.
Once the tank is secured, add the caps to the bolts to further secure the toilet. Then connect the water supply line to the tank, re-attach the fill valve, and turn the water main back on. Flush the toilet several times to look for any leaks, then check down around the base of the toilet to make sure everything is properly sealed.
How do you lift and reinstall a toilet?
Lifting and reinstalling a toilet is a fairly straightforward process. Here are the steps to follow:
1. Turn off the water supply to the toilet.
2. Flush the toilet and use a sponge to remove any remaining water in the tank and bowl.
3. Unscrew the water supply line from the toilet.
4. Unbolt the floor bolts from the bottom of the toilet, using a wrench.
5. Carefully lift the toilet from the floor and set it aside.
6. Clean the flange and area around it.
7. Place a new wax ring on the flange.
8. Slide the bolts in the bottom of the toilet, making sure to line them up with the holes in the flange.
9. Carefully place the toilet back in position on the flange, pushing down evenly on all sides.
10. Tighten the bolts in the base with the wrench.
11. Reattach the water supply line and turn the water supply back on.
12. Test the connection by flushing the toilet.
13. If everything is working properly, seal any exposed bolts with plumber’s putty.
Can you move a toilet back?
Yes, it is possible to move a toilet back to a previous location. Depending on the type of toilet you have, there may be several steps required to move it. If the toilet is on a concrete floor, you may need to first remove the wax ring that seals the connection between the floor and the toilet, as well as any caulk that helps secure the toilet in place.
If the toilet was previously connected to the drain system, you will likely need to detach it and reassemble the plumbing connections with new fittings. You will then need to level the toilet by adjusting the bolts beneath the base, re-seal the connections, and re-caulk around the base of the toilet.
Are back to wall toilets easy to install?
Yes, back to wall toilets are generally quite easy to install. Depending on the type of back to wall toilet you purchase, the installation process may vary slightly. Most back to wall toilets require only a few simple steps to get set up, such as attaching the toilet to the wall and floor, connecting the supply line to the toilet, and securing the inner components of the toilet.
While this is typically a relatively straightforward process that most DIY homeowners can complete, having a professional plumber perform the installation is always a good idea. This ensures a proper fit and secure connections, as well as the peace of mind that comes with knowing the installation is done correctly.
How hard is it to reroute a toilet?
Rerouting a toilet can be quite challenging and time consuming. Depending on the specific plumbing job, it can require some basic plumbing knowledge and tools. To reroute a toilet, you will need to physically remove the toilet, cut a new hole in the floor and attach a new piping system or adjust the old one.
You also need to be familiar with the specific type of flange, drain and fittings you will be using and have the proper tools to fit everything together correctly. It’s important to also ensure that when rerouting the toilet, you are doing it up to the local codes.
If any aspect of the rerouting is done incorrectly, you can end up with clogged pipes and problems with the internal parts of the toilet, like the valves and flapper. Re-routing a toilet is a lengthy, intricate process, and definitely not something that should be done on a whim.
How do I get back to wall toilet cistern?
To get back to a wall toilet cistern, you will need to begin by draining the tank of any remaining water. This can be done by turning off the water valve and lifting the float arm to cease water entering the tank.
The outlet valve at the base of the tank can then be opened to allow remaining water to escape, and the tank can be emptied. Once this is done, the bolts securing the tank to the wall will need to be removed, and the tank lifted down from the wall.
The outlet and inlet pipes must then be disconnected at the tank, and the tank’s mounting bracket taken down. The new cistern should then be placed in the mounting bracket and reconnected to the existing incoming water supply and outflow pipes.
Finally, the tank should be secured to the wall of the toilet with the supplied screws or bolts and the water valve should be turned on to test that the cistern is properly connected.
Can you rotate a toilet 90 degrees?
Yes, you can rotate a toilet 90 degrees, however, it requires quite a bit of effort to accomplish the task. If the toilet is freestanding, it is quite a bit easier to rotate it to the desired position.
However, if it is attached to the floor, it will require you to detach it from the floor and re-angle the pipes and connectors which are connected to the base of the toilet. You will also need to disconnect the water supply pipe in order to have access to the toilet’s base.
Once the toilet is detached, you can rotate it and reattach it to the floor.
It is important to note that rotating the toilet may require additional plumbing work, such as the need to adjust the height of the flange that connects the toilet to the floor, if the angle of the toilet is not close to 90 degrees.
Additionally, it is recommended to use a professional plumber to ensure that the connections to the base of the toilet are secure and properly functioning.
How much does it cost to move a toilet in a bathroom?
The cost of moving a toilet in a bathroom will vary depending on a number of factors. For starters, if the toilet being moved is a standard one-piece model, the cost will be relatively low, as all that needs to be done is disconnecting the water supply line and unscrewing it from the floor.
However, if the toilet is a two-piece model, which requires uninstalling and reinstalling the wax seal and tank, the work becomes substantially more complicated, and consequently more expensive. Additionally, if the original location of the toilet is connected to plumbing in the walls, moving it can require rerouting those pipes, which increases the complexity and cost of the job.
All told, the cost of the entire process can range anywhere from $75 to $500, depending on the complexity of the move and the time it takes to complete it.
How much to remove a toilet and put it back?
On average, it can cost anywhere from $125 to $250 to remove and replace a toilet. However, the cost may vary depending on the type of toilet, the difficulty of the installation and whether other elements such as water supply lines or a wax ring are needed.
Additionally, the cost may be higher if you hire a plumbing expert to handle the job. In most cases, it is best to hire a professional plumber if you do not have the proper expertise and knowledge needed to remove and reset the toilet.
Do you need planning permission to move a toilet?
In most cases, it is not necessary to obtain planning permission to move a toilet in a dwelling house, unless the proposed works involve a change of use, a new partition wall, or a change of external appearance.
If the relocation of a WC is internal, with no alteration to the external appearance of the property, then planning permission is not required provided the proposed works are within the permitted development rules.
For those considering works outside of the scope of permitted development, and the local authority is consulted with an application for a lawful development certificate, they may accept the relocation of a WC within an existing private dwelling house if the works do not detract from the general amenity of the area.
If any alteration to the external envelope of the property is proposed, it is likely that planning permission will be required. This would include the altering, rebuilding or enlarging of the building itself, including any means of access, and the provision of windows, balconies and other means of lighting, ventilation and access.
It is important to remember that in some cases, it is not possible for the works to be accepted as permitted development, therefore it is always advised to consult the local planning authority prior to proceeding with the works.
Can you install a toilet yourself?
Yes, it is possible to install a toilet yourself. However, it is a difficult and involved project that may require basic plumbing knowledge, especially if the toilet is completely new. Generally, the process involves disconnecting the old toilet, removing it, and readying the floor for the new toilet’s base.
Once the floor is set, the new toilet’s drain line must be connected to the existing plumbing system and sealed. The tank must also be connected and assembled. Finally, the seat must be securely locked in place.
Depending on the type of bathroom you have, the process may involve opening walls, drilling and tapping the floor, and taking additional steps. Installing a toilet may be possible as a DIY project, however it is always best to consult an experienced plumber to ensure that the work is properly done.
How do you install a toilet for beginners?
Installing a toilet for beginners can seem like a daunting task, but with a few tips and tricks, it can be done quite easily. Here are the basic steps for installing a toilet for beginners:
1) First, turn off the main water valve and flush the old toilet to make sure there is no water left in the bowl or the pipes.
2) Remove any old wax seals and bolts from the old toilet.
3) Install the toilet bowl onto the floor using a wax seal and bolts. Make sure the wax seal is tightly secured to prevent any water leakage.
4) Install the wax ring onto the new toilet. This should have come with the toilet, or you can purchase it separately.
5) Connect the toilet bowl to the floor with a new wax seal and mounting screws. Make sure everything is tight and secure.
6) Connect the supply tube to the bottom of the toilet tank. Use a wrench to make sure it is attached correctly.
7) Connect the new toilet tank to the toilet bowl.
8) Connect the supply line to the wall. This can be done with a wrench or a plumbing tool.
9) Tighten all bolts and screws to make sure the toilet is secure.
10) Turn on the main water valve and check for any leaks.
Once all these steps are completed, you should have successfully installed your new toilet for beginners! Although it may seem complicated, following these steps should make it a breeze. Good luck!
What is the average labor cost to install a toilet?
The average labor cost to install a toilet will depend on a few factors. Generally, the cost of labor to install a toilet will range from $225-$500, depending on factors such as the complexity of the installation and the contractor’s overall rate.
If a plumber needs to change pipes or the sewer line, the cost can increase to around $700. Additional costs such as permits, part costs, removal and disposal of the old toilet, or hauling away of the waste water and refuse can also drive up the overall cost significantly.
Homeowners should consult a professional plumber to get an accurate estimate of the labor cost.
What to know before installing a toilet?
Before installing a toilet, there are a few things you should know. First, make sure the floor is level. A level floor will make sure that your toilet is stable and won’t rock. Second, gather the supplies you will need to install your toilet.
You’ll need a new wax ring and bolts, a toilet shim, a wrench, a rubber mallet, plumbers putty and glue, a hacksaw or an adjustable wrench for tight areas, and the toilet itself. Third, turn off the water supply to the toilet.
Make sure to turn off the water by shutting off the valve behind the toilet or in the basement or above the ceiling. Fourth, remove the old toilet. To do this you will need to remove the two bolts connecting the toilet to the floor and then lift the toilet off the floor flange.
Fifth, inspect the flange. Look for any signs of damage or rot. If the flange is damaged, you will need to replace it. Sixth, use the new wax ring to seal the toilet. Seventh, properly secure the toilet to the floor.
Once the toilet is secured to the flange, you can replace the water supply line and turn the water back on. Finally, test the toilet by flushing. If the toilet is flushing properly, the installation is complete.
What kind of toilet is easiest to install?
The most straightforward toilet to install is a Two-Piece Toilet. This style is the most popular and is composed of two pieces – the tank and the bowl. They come pre-assembled and can be easily screwed into the floor.
Installation is quite simple and may require the assistance of a professional in some cases. Aside from the key components, installation of a Two-Piece Toilet typically doesn’t require much more than basic tools, such as a screwdriver, pliers, and a wrench.
Most come with all needed instructions for installation and maintenance. Generally, a Two-Piece Toilet can be installed in just a few hours.