When installing a single post toilet paper holder, the general rule of thumb is to face the axle of the post away from the toilet, so that the TP is facing you directly when seated on the toilet. This makes it easier to reach the toilet paper without having to awkwardly reach behind you.
Additionally, it should be placed in an area that is easy to reach while seated. Ideally, the toilet paper holder should also be placed at a height that is comfortable to reach while seated. In most cases, this will be around chest or shoulder height.
Is there a correct way to place toilet paper holder?
Yes, there is a correct way to place a toilet paper holder. The correct place to hang a toilet paper holder is on the wall that is closest to the user. This keeps the toilet paper holder close enough for easy use, yet far enough away to avoid hitting it with the back of your legs or feet when you sit down on the toilet.
In addition, a common error is to place the holder too low. To avoid this mistake, make sure the toilet paper rolls are at least 15 inches (38 cm) above the floor. When possible, hang the holder so that it’s centred between the toilet and the wall.
If you’re installing a double-roll holder, make sure there’s an adequate space between the holders to accommodate both rolls comfortably. Lastly, it’s important to make sure the holder is firmly mounted to the wall or the door and is securely screwed in.
How do you install an inset toilet paper holder?
Installing an inset toilet paper holder is relatively simple, and can be done in just a few easy steps.
First, prepare the area where the toilet paper holder will be installed. Make sure the wall is clean and free of any debris. If you’re installing the holder into drywall, it may be helpful to use a stud finder to make sure you’re drilling into a stud.
Mark the area where you will drill the hole.
Next, you’ll need to use a drill and bit that matches the size of the holder’s mounting bracket. Make sure your drill is set to reverse, as this will make it easier to screw the holder into the wall.
Drill the marked area and make sure the hole is deep enough for the bracket.
Finally, you can install the inset toilet paper holder. Place the mounting bracket into the hole and tighten the screws. Adjust the bracket if needed, and attach the toilet paper holder to the bracket using the provided hardware.
Once in place, it’s a good idea to test it out by placing some toilet paper on the holder, making sure it stays in place before you finish up.
Do recessed toilet paper holders save space?
Yes, recessed toilet paper holders do save space. They are mounted inside the wall and are out of the way, freeing up wall and counter space. This design allows for a cleaner, sleeker look than a standard toilet paper holder that sits out from the wall.
People who live in apartments and other small spaces often opt for a recessed toilet paper holder due to its space-saving design. Additionally, these holders are great for bathrooms with minimal decor; their subtle design won’t detract from the overall aesthetic of the room.
Some also come with a storage shelf, allowing more items to be stored above the toilet. If you’re looking for a way to free up some space in your bathroom, you should consider a recessed toilet paper holder.
How do you tighten a toilet paper holder with hidden screws?
When a toilet paper holder has hidden screws, it means that the screws are concealed behind a shield, panel, or cap of some kind. To access and tighten the screws, the holder needs to be partially dismantled.
To begin, take a look at the back and underneath the holder to identify how it is held in place, and what parts need to be removed to access the screws. Most toilet paper holders are held together with either a few small screws or plastic pressure clips, which can be easily removed with either a flat head screwdriver or needle-nose pliers.
Once the holder is disassembled, you should be able to locate the screws behind the panels. The screws can then be tightened with an adjustable wrench or a screwdriver to secure the toilet paper holder in place.
After you have finished tightening the screws and re-installed the respective parts, the toilet paper holder should be secured and ready to use.
How do you tighten a toilet seat with no access underside?
If you have a toilet seat that does not have access from the underside, you can still tighten it. First, you will need some basic supplies, such as a putty knife, a screwdriver, and a spanner (or adjustable wrench).
Depending on the type of seat, you may also need some replacement parts. With all of your supplies ready, follow these steps:
1. Loosen the top nuts on either side of the seat and remove them.
2. Carefully lift the toilet seat off of its hinges.
3. Place the putty knife between the seat and the bottom of the tank to help hold the seat in place while you work.
4. With the screwdriver, remove the screws that attach the seat to the mounting bolts underneath.
5. With the spanner or adjustable wrench, loosen the mounting nuts beneath the seat and then remove them.
6. If you need new parts, install them now.
7. Secure the seat back onto the mounting bolts and tighten the nuts using the spanner or adjustable wrench.
8. Place the seat over the mounting bolts and tighten the nuts from the top using the screwdriver.
9. Test the seat for stability and make sure the nuts are tight but not overly tight.
Following these steps should help you tighten a toilet seat with no access from the underside. If you need additional help or supplies, consult your local home improvement store or plumbing professional.
How do you tighten a concealed toilet bolt?
Tightening a concealed toilet bolt is a relatively simple task. First, you will need to locate the bolts. These are typically located on the back side of the toilet, located just beneath the seat. When the seat is lifted, you will be able to see the bolts.
However, access may be blocked by either the tank or the bowl itself. In order to gain access to the bolts, you may need to disconnect the water line or remove the toilet tank using a wrench.
Once you have located the bolts, you will need to tighten them. Begin by taking a socket wrench and attaching it to the nut of the bolt. Make sure the wrench is snug, then turn the nut clockwise to tighten the bolt.
Make sure to not overtighten, as this could cause the bolt to snap.
After you have tightened the bolt, reinstall the toilet tank and reconnect the water line. Make sure the nut is tight and no longer able to be adjusted by hand. Once completed, turn the water back on and check to see that the toilet is firmly secured to the floor.
How do you tighten American Standard toilet seat with hidden bolts?
To tighten an American Standard toilet seat with hidden bolts, you will need to access the two bolts that are located underneath the seat. Depending on the model of toilet you have, these bolts may be covered by a plastic covering which can be manipulated off the bolts.
Once that is removed, use a screwdriver to turn the bolts in a clockwise direction, to make them tighter. When you think that the seat is tight enough, you can replace the plastic covering and test it out by pushing down on the seat.
If it feels loose, then repeat the process until you are happy with the tightness of the seat.
Why won’t my toilet seat screws tighten?
It could be possible that your toilet seat screws are not properly tightened for a few reasons.
Firstly, it could be that the screws have become damaged and do not fit properly anymore. This could be caused by frequent wear and tear, or improper installation. In this case, you will likely need to replace the screws to ensure a secure fit.
Another possibility is that the threads of the screws are not long enough to fit into the holes on the toilet seat and, as a result, the screws cannot be tightened. This can also be remedied by replacing the screws.
Finally, it could be that the holes that the screws are meant to fit into have become worn out, making it impossible to secure them. This can happen over time due to repeated use of the toilet seat, which can lead to the holes becoming enlarged.
In this case, you would likely need to replace the toilet seat in order to secure the screws.
Whatever the cause may be, it is important to ensure that the screws are secure so that your toilet seat does not become loose and unstable.
How do I stop my toilet seat from moving sideways?
The simplest and most economical option is to use rubber bumper stops that can be purchased at most hardware stores. These simply fit onto the toilet bowl and stop the seat from sliding around. Alternatively, you can also purchase metal stabilizers especially made for toilet seats.
This involves attaching metal stabilizers on the underside of the seat, which act as brackets that hold the seat in place. Both of these solutions can easily be installed in minutes using basic tools.
If you want a more permanent solution, you can even install threaded inserts into the bowl, allowing you to anchor the seat directly to the bowl. Finally, if your toilet seat is cracked or broken, it may be best to replace it completely as this will provide the most secure fit.
What happens if you over tighten toilet bolts?
If you over-tighten the toilet bolts when installing or replacing the toilet, you can damage the wax seal or even your new toilet itself. Over-tightening the bolts can also lead to fractures and leaks around the base of the toilet.
This can be a major problem, as water can leak through the fractures and cause damage to both the floor and the ceiling below it. Over-tightening the bolts can also cause them to strip the threads in the bowl, making it difficult to secure your toilet properly.
Additionally, if over-tightening damages the wax seal, it will no longer be able to form a watertight seal, resulting in water leaking out from the edges of the bowl. It can be difficult to undo the damage caused by over-tightening, and often requires the help of a qualified plumber.
What are the different types of toilet seat fittings?
The four main types of toilet seat fittings are screw down, snap-on, bolt-on, and slip fit.
Screw down toilet seats are the most common and are typically attached with two or three screws. These are easy to install, as they’re just screwed straight into the toilet bowl, and require minimal effort to adjust.
Snap-on toilet seats latch onto the bowl via a series of clips and pegs. They’re usually easier to install than screw-down seats, but can be less stable over time.
Bolt-on toilet seats are the most secure type, and are typically attached to the bowl with one or two bolts. These seats can be less comfortable due to the fact that they don’t move, but they’re very secure and unlikely to come off or break.
Finally, slip fit toilet seats fit snugly over the bowl without the use of bolts or screws. These are usually the easiest to install, as many don’t even require tools, but they’re also the least secure of the four types and can come off easily.