Whether the lever should be up or down to drain a tub depends on the type of tub drain. If the tub is equipped with a lift-and-turn style drain, the lever should be turned to the right (horizontal) position to open the drain.
If the tub is equipped with a toe-touch style drain, the lever should be turned to the left (vertical) to open the drain. In both cases, the lever should be turned in the opposite direction to close the drain.
Which way do you turn a bathtub drain?
When replacing or installing a bathtub drain, you must turn it in the correct direction in order for it to work properly. To determine the correct direction, first look for the shorter tongue or boss on the drain body.
This shorter tongue should point toward the rear of the bathtub, or toward the wall, when the drain is installed. The longer tongue should be pointing toward the center of the bathtub, or away from the wall.
It is important to note that in some instances, the longer tongue may be facing downward when installed.
Once the drain is correctly positioned, the drain flange should then be turned and tightened until it is securely fastened to the bathtub. Once the drain flange has been appropriately secured, the tub strainer and stopper can then be installed.
When replacing or installing a bathtub drain, make sure to check the drain instructions carefully and to turn the drain in the correct direction. Doing so will ensure the bathtub drain works properly.
How does a bath tub trip lever work?
A bath tub trip lever is a handle mounted to the overflow pipe that is used to control the bathtub drain. When the handle is pulled up, the drain opens, allowing water to escape from the bathtub. When it is pushed down, the drain closes, allowing the tub to fill up.
The trip lever is made up of a few components. Inside the overflow pipe is a stopper rod that is activated when the handle is pulled up or pushed down. The rod is attached to a linkage that pulls the stopper up or pushes it down into the drain, thus opening or closing the drain.
Additionally, the lever itself is connected to a mechanism known as an overfill prevention float. This device will shut off the water when the bathtub is almost full, preventing it from overflowing.
Do you push the drain up or down?
It depends on the type of sink you have. If you have a stopper type sink, then you typically push the drain up to close it and down to open it. If you have a pop-up type sink, then you would push the drain down to close it and up to open it.
Additionally, there may be a specific lever or knob that is used to keep the drain open or closed, depending on the sink. Some sink types may also require an additional tool, such as a pair of pliers or an Allen wrench, to open or close the drain.
It’s important to read the instructions to make sure that you are operating the drain correctly.
How do you snake a tub drain with a lever?
Snaking a tub drain with a lever can be done either manually by hand or with a power drill. If using a hand lever, wrap the drain with a wet rag to protect the surface. Insert the lever into the drain and twist it so that the snake goes into the drain as far as it will go.
Gently pull the handle to pull the snake out of the drain, pushing the clog down the drain as you go. Continue to pull the snake out of the drain until the clog has been cleared. If using a power drill, insert the power drill bit into the drain and twist to make sure it is secured.
Then, turn the power drill on and press the trigger to spin the snake into the drain. Do not push the snake too far into the drain or you could break the pipe. Once the snake is in the drain, pull the trigger to spin the snake in the opposite direction to move the clog away.
If the clog is still not cleared, you may have to repeat this process multiple times. When the clog has been cleared, turn off the power drill and remove the bit from the drain.
How do you adjust a trip lever bathtub drain?
To adjust a trip lever bathtub drain, you will need to first locate the adjustment nut. This nut is located under the bathtub’s access panel or faceplate, or is part of the trip lever body itself. To access the adjustment nut, remove the access panel or faceplate and unscrew the nut.
Once the nut is accessible, you will need to remove the trip lever body. To do this, you will have to unscrew the faceplate screws or detach the body from the linkage to the waste and overflow tube. This can be done by unscrewing the screw or by pushing down on the clip holding the body to the linkage.
Once the trip lever body is removed, you can adjust the tension of the spring. To do this, you will insert a flathead screwdriver into the opening on the bottom of the trip lever body and turn it counterclockwise to loosen the tension.
If you are unsure how tight to adjust the spring, it is best to turn it two to three revolutions to make sure it stays in place.
Once the spring tension has been adjusted, you will need to reattach the trip lever body to the linkage. This can be done by screwing the screw or pushing down on the clip to reattach the body. Once in place, you can test the trip lever by pushing down on the lever to make sure it is working properly.
Finally, reinstall the access panel or faceplate and screw in the nut to secure the trip lever body.
Adjusting a trip lever bathtub drain requires some basic knowledge of plumbing and should be done with caution as any adjustments to the spring tension can wear down the internal components of the bathtub’s drainage system over time.
How do you fix a trip lever?
Fixing a trip lever requires identifying the issue first, then taking a few steps to address it. First, inspect the lever and its components for any obvious signs of wear or damage. If the lever is not working properly, the most likely culprit is the linkage, which connects the lever to the drain.
Check this linkage and adjust the tension if necessary. If the linkage appears fine, then you may need to replace the trip lever itself. To do this, you first need to remove the lever from the drain.
To do this, you can use a screwdriver or wrench to remove the screws that hold the lever in place. Once the lever has been removed, you can replace it with a new one. You can either purchase lever replacements from any plumbing store, or, if possible, you can purchase a new lever to fit your existing drain.
Once you have the new lever in place, you can reattach the linkage, adjust the tension, and test the lever to ensure it is working properly.
Can you replace bathtub drain lever?
Yes, replacing a bathtub drain lever is a relatively easy task that most people can accomplish. It’s a good idea to familiarize yourself with the drain assembly before starting the project. To replace a bathtub drain lever, you’ll need a few basic tools: a screwdriver, adjustable wrench, and a plumber’s putty knife.
Be sure to read the manufacturer’s instructions prior to beginning.
To begin, remove the cover from the drain and shut off the water supply. Use a screwdriver to remove the screws connecting the lever to the drainpipe, then remove the lever from the drain. To make sure you place the new lever correctly, it may be a good idea to take a picture of the existing setup before making changes.
Insert the new lever into the drain assembly and secure with the screws you removed earlier. Lastly, reapply the cover and turn the water back on.
Always be sure to follow the manufacturer’s instructions. If the drain assembly doesn’t look like what you expected or if you run into troubles, it’s best to hire a professional plumber.
What is the bathtub drain lever called?
The part of a bathtub drain that is used to open and close the water flow is typically referred to as the bathtub drain lever. It is designed to control the rate at which water flows out of the bathtub, and is usually located near the faucet.
In some cases, it can even be found underneath the drain assembly. It is typically made of metal, plastic or rubber and is connected to a rod or chain that runs up to the overflow and leverages the actual drain.
It is important to properly maintain the drain and lever in order to avoid costly repairs.