Yes, it is very easy to change a regular shower head to a handheld. You will need to unscrew the existing shower head and then replace it with a new handheld showerhead. You may need to use some tools such as a wrench or pliers to assist in unscrewing the existing shower head.
There are also instructions included with the handheld shower head which will guide you step-by-step through the process. Once the showerhead is fitted the connection hose should be attached following the instructions provided and the shower head should be tested before use.
You may also need to purchase some additional accessories such as a wall-mount or adjustable shower arm to complete the installation of your new handheld shower head.
How do you install a handheld shower head for an existing shower?
Installing a handheld shower head for an existing shower often requires replacing the existing shower head. First, you’ll need to shut off the water supply, calculate the type of pipes you will be attaching the showerhead to (typically 1/2-inch pipes) and determine the correct connector type (i.
e. , compression, threaded, etc. ).
Once you have the correct connection type, begin by unscrewing the existing shower head, using a wrench if necessary. Use a flexible hose clamp and teflon tape to seal the connection between the hose and the wall.
Attach the shower head to the other end of the hose, using the same method as before. If applicable, install the diverter and secure it to the wall.
After the diverter is installed, turn the water supply back on and test the head. If it leaks, turn off the water supply, double-check the connections, and re-secure them. Finally, turn the water supply back on and check for any further leaks.
You should now have a fully functioning handheld shower head setup in your existing shower.
Can you put any shower head on a shower?
The answer is yes, you can put any shower head that you like on your shower. However, it is important to make sure that you choose the right size of shower head for your shower. If the shower head is too large, it may not fit the existing piping and could potentially cause water damage to your bathroom walls or ceiling.
Additionally, if the shower head is too small, it may not provide adequate water pressure or coverage. When in doubt, it is always best to consult an experienced plumber or shower fixture expert who can suggest the right shower head size and material for your shower.
Are handheld shower heads worth it?
Handheld shower heads can be a great value and worth the money. They provide more convenience and versatility than standard shower heads and are great for various bathing needs. Handheld showerheads can be used to rinse off after a bath or shower, lather up with body wash or shampoo, or even for rinsing off animals or small children.
Additionally, many of them come with adjustable settings, such as mist or rain, so you can select the spray pattern to best suit your needs. Many of them also come with a long or swivel hose, so you can reach all areas of the shower or bath with ease.
Overall, handheld shower heads can provide a lot of benefits and are definitely worth it.
Do you need a diverter valve for a handheld shower?
A diverter valve is not absolutely necessary for a handheld shower. However, it can be helpful in providing a choice of two shower heads – one fixed and one handheld. A diverter valve connected to the water pipe routes part of the water supply to the handheld shower head and the remaining part to the main one.
This valve is useful when there is only one shower head in existence and you want to be able to enjoy the experience of a handheld shower. Alternatively, some showers come with built-in diverter valves, thus allowing you to enjoy the convenience of two shower heads while taking advantage of the same water pressure.
Therefore, whether or not you require a diverter valve for a handheld shower depends on what type of shower head you have, and whether or not a separate diverter exists.
Do I need an electrician to fit a shower?
Yes, in most cases you will need an electrician to fit a shower. An electrician can help you with all the necessary wiring and connections while bringing your shower up to the required safety standards.
In addition, certain showers require special electrical components and wiring that only an experienced electrician can provide. Electricians also know how to connect your shower to the main water supply, ensuring it works safely and efficiently.
Additionally, a qualified electrician will be aware of any applicable regulations when making the connections, so it is highly recommended that you use one for this type of job. It is important to ensure your electrician has adequate experience in working with showers and is up to date on any electrical codes that may apply to your shower before they start the project.
How do I divert my shower water?
Installing a shower diverter valve is the best way to divert your shower water. This allows you to switch between a handheld shower head and the regular shower head. To install a diverter valve, start by turning off the water supply to the shower.
After the supply lines are shut off, use a wrench to unscrew the diverter pipe. Once the pipe is removed, attach the diverter valve to the shower wall. It usually comes with the appropriate screws and anchors.
Connect the supply lines to the new diverter valve using the correct fittings. Once the valve is in place and secured, turn the water supply back on and test your diverter valve to make sure it works properly.
If the diverter isn’t working correctly, you may need to consult a plumber for assistance.
What is a shower head diverter?
A shower head diverter is a handy device that helps to redirect the flow of water between multiple shower outlets. It is essentially an advanced form of a water spigot and is typically found in bathrooms as a part of a shower unit.
It can be used to control and efficiently manage the flow of water from two or more outlets in the bathroom. Its main purpose is to help control the flow of water from two or more sources, and it does this by diverting, or redirecting, the flow of water either to one outlet or to the other.
This helps to prevent water from all outlets being simultaneously or overflowing, as well as providing more convenience when showering or bathing. For example, you can use it to divert water away from the handheld-showerhead while you are shampooing your hair, and then switch it back once you have finished.
Shower head diverters also aid in saving water by ensuring that water is not unnecessarily wasted.
Where is the flow restrictor in a hand held shower head?
The flow restrictor in a hand held shower head is typically located inside the shower head itself. To access it, you need to first remove the shower head by unscrewing it using a wrench or pliers. Once you have removed the shower head, you will see a metal casing that houses the flow restrictor inside of it.
This can usually be easily removed by unscrewing the cap or retaining screws. Once the caps or screws are removed, you should be able to take the flow restrictor out. When reassembling the shower head, make sure that the O-ring and flow restrictor are correctly positioned to ensure a tight seal and to avoid leakage.
How do you raise a shower head without moving plumbing?
Raising a shower head without moving plumbing is relatively easy and can be accomplished in a few simple steps. First, you will need a screwdriver, an adjustable pipe wrench, a towel, and some plumber’s tape.
Begin by shutting off the water to the shower. Wrap the pipe wrench securely around the pipes coming up from the shower head. With an adjustable wrench, carefully loosen the nut connecting the shower arm to the wall.
Be sure to keep the shower arm securely in your hands. Once all connection points are loosened, you can begin to raise the shower head. When you’ve lifted it to the desired height, use plumber’s tape to secure it in place.
Tighten the nut with the wrench, then carefully test the connection for leaks. Finally, turn the water back on. After these steps are completed, the shower head should be firmly in place, raised without the need for added plumbing.
What is the difference between a shower diverter and a shower valve?
A shower diverter and a shower valve are two different components used in a shower system. A shower diverter is a basic plumbing fixture that diverts water from the showerhead to a hand sprayer or tub filler, allowing a user to selectively switch between the two water sources as needed.
It is an inexpensive plumbing item and is typically made of plastic.
On the other hand, a shower valve is much more complex and is used to control various features of the shower including water flow, temperature, and pressure. It is typically made of metal or brass and installed in the wall behind the showerhead.
A shower valve manages the temperature and pressure of the water flowing through the shower and requires a licensed plumbing expert to install and maintain.
How do you shower without touching water?
Showering without touching water can be done by using a specialized showering apparatus. These devices typically involve either a long, extendable handle or a remote-control that allows you to control the water flow, temperature, and pressure.
Additionally, you will need to buy a showerhead with a “hands-free” feature which disperses droplets of water while you shower — this way, you don’t have to get your hands wet. There are even showerheads that feature voice-activated controls.
Once your showerhead is installed, you’ll also need a shower wand that has a gripping mechanism on one end and a water-spitting nozzle on the other. You simply stretch out the wand and point it towards your body to direct the water at yourself.
This way, you can shower without ever having to touch a single drop of water.
To maximize your comfort, you can also opt for a shower liner that has a special pocket for inserting a wireless handheld showerhead. That way, you won’t have to extend the shower wand for every move you make.
Plus, the water temperature and pressure can easily be adjusted with a remote-control.
Not only is this type of showering effortless, but it’s also incredibly hygienic. Plus, it’s much more convenient than a traditional shower, as you don’t need to step into a wet, slippery tub or shower.
You can get a good all-over shower without ever having to stand in the water.
Do you need a shower diverter?
Yes, you do need a shower diverter if you want to be able to divert the flow of water between two sources. A shower diverter is usually placed in the wall and allows you to switch between multiple shower valves, like a hand shower, overhead shower, and body sprays.
Many shower diverters include a built-in control handle that lets you easily divert the water from one output to the other, or even shut off the water flow altogether. In addition to enabling you to use different outlets for showering, having a shower diverter installed can also help save water because you don’t have to keep running the full-on hot and cold water at once.
This can result in lower water bills. A shower diverter is a great addition to any bathroom, but it’s important to find one that is properly sized and compatible with the existing plumbing fixtures in your shower.
If you’re not confident in your ability to install a shower diverter on your own, you can always have a professional do the job to ensure it is installed correctly and safely.
How much does it cost to put in a shower diverter?
The cost of installing a shower diverter will depend on several factors, including the type of shower diverter you choose and the complexity of the installation. A basic three-handle diverter valve can start at around $20, while replacing an existing shower valve can run from $150 to $200.
High-end, designer valves or specialty diverters can range from $200 to $500 or more for the supply parts. Depending on the complexity of the installation, you may also need to factor in additional costs for the labor.
Professional plumbers typically charge between $60 to $100 per hour, with most installations carrying a minimum fee of around $100 to $150, so the labor costs on a shower diverter installation can range from $100 to $250 or more.
Altogether, the total cost of installing a new shower diverter can range from as little as $120 to over $800 or more, depending on the type of diverter and the complexity of the installation.