Changing the water filter on a Whirlpool side-by-side refrigerator is not a difficult task. Depending on the model of refrigerator, there are a few steps to follow in order to replace the filter.
1. Locate and open the refrigerators filter cover located inside the refrigerator, typically located in the upper-right-hand corner or near the bottom-right side.
2. Remove the old filter. You can either twist and pull it out or press the button to unlock it and pull it out.
3. Take the new filter and remove the protective cover.
4. Insert the new filter. Press the button to lock it in place or twist and lock it.
5. Close the filter cover.
Once you have followed the steps above, your Whirlpool side-by-side refrigerator’s water filter has been successfully changed. It is recommended to change the filter every six months, or more often if the water pressure is low or the water tastes odd.
Where is the water filter on a side by side?
The water filter on a side by side refrigerator is typically located inside the unit, either on bottom near the floor, or at the top in an interior compartment. The exact location of the water filter will depend on the model and brand of your refrigerator.
To find the location, consult your user manual for your specific refrigerator.
Once you’ve located the filter, you will need to replace it every 6 months or as recommended by the manufacturer. To replace the filter:
1. Open the compartment where the filter is located inside the fridge.
2. Remove the old filter.
3. Push the new filter into place.
4. Close the compartment.
5. Run water through the filter for 5 minutes to flush it out and check for any leaks.
If you have a refrigerator with an external water filter, the filter is usually located at the bottom of the appliance and can be accessed after you remove the grille. For further troubleshooting, consult your refrigerator’s user manual.
How do I reset my Whirlpool side by side water filter?
To reset the Whirlpool side by side water filter on your refrigerator, follow these steps:
1. Locate your Whirlpool refrigerator filter and locate the reset button on the side or the top.
2. Press and hold the reset button for 15 seconds.
3. After 15 seconds, release the reset button. The reset will be complete.
It should be noted that you should not reset your Whirlpool refrigerator filter too often as this may cause damage. It is usually necessary only after changing the filter or when the water flow slows down or stops.
If your water filter does not reset after pressing the reset button, you may need to replace it. Additionally, some refrigerator models require the use of a paperclip or similar object to press the reset button.
How do you change a Whirlpool refrigerator Everydrop filter?
Changing the Everydrop filter in a Whirlpool refrigerator is a very simple process. First, make sure the refrigerator is unplugged and the water shut off. Locate the filter, which should be either in the top right corner or the bottom left corner of your refrigerator (depending on the model).
Pull down the filter cover and pull the filter straight out.
Next, take the new filter and align the arrows on the filter and the filter insert with the water flow direction. Carefully insert the filter, making sure it is all the way in. Finally, close the filter cover and place the knob back in the drill hole.
After replacing the filter, you will need to flush the system and reset the filter. To do this, turn the ice and water off, remove the filter, depress the reset button on the grille, and finally turn the water and ice back on.
Can you change a refrigerator filter without turning off the water?
Yes, you can change a refrigerator filter without turning off the water. The first step is to locate the water filter and remove it from the refrigerator. Next, locate the shut-off valve for the refrigerator water line and turn it off, to prevent any water from entering the filter while it is being replaced.
Once the valve is off, you can remove the old filter and install the new one. Be sure to refer to your refrigerator’s manual when locating the water line or installing the new filter. Once the new filter has been inserted, turn the shut off valve back on and the water will automatically begin to flow through the filter.
Remember, it is important to follow any instructions that came with the filter when replacing it.
Can I run my Whirlpool refrigerator without a water filter?
Yes, you can run your Whirlpool refrigerator without a water filter. However, this is not recommended due to the potential risks that can come with using unfiltered water. When using unfiltered water in your refrigerator, there is a risk of consuming impurities that can cause health problems.
In addition, not using a filter can damage the other components of your refrigerator, such as the water lines and the ice maker, which will require costly repairs and can even reduce the efficiency of your appliance.
Furthermore, all refrigerator models need to be cleaned periodically to remove mineral buildup. Without the filter in place, this buildup will increase and will likely require more frequent and extensive cleanings.
Do you have to turn off the water supply to change a refrigerator filter?
Yes, in order to properly change a refrigerator filter, you must turn off the water supply to the refrigerator. To do this, you need to turn off the water valve that supplies the water to the refrigerator.
Some refrigerators located near the back, near the wall, have a shut-off valve located directly behind them. Other refrigerators, such as side-by-side models, often have the shut-off valve located in the basement or in a nearby utility closet.
Once the water supply is turned off, you can proceed with changing the filter.
How much water do I need to run after changing my refrigerator filter?
You should always run at least two to three gallons of water through the new refrigerator filter after installation. This flushes out any small particles, impurities, or foreign matter that may have entered the filter during the manufacturing or installation process, and ensures that the refrigerator water filter is working properly and providing your family with clean and great-tasting drinking water.
It is important to note that it’s not necessary to run the full capacity or quantity of water that the filter can hold through it, as that amount of water will take too long to flush out the filter. To get the most efficient flushing of your new filter, about two to three gallons of water should be all that’s necessary.
How long should you run water after changing filter?
It is important to run water for about 5 minutes after replacing or changing a water filter to ensure it works correctly and to prevent any particulates or pollutants from entering the water supply. During this time, it is important to allow the water to run from an outside hose bib or faucet until the water runs clear.
If the water does not run clear in 5 minutes, then it is recommended to replace the filter again. It is also important to note that the time to replace a water filter depends on the type of filter being used, as some filters may require longer run times than others.
In any case, it is important to refer to the manufacturer’s instructions for a specific filter to determine how long the water should be run after it has been changed.
Where is my refrigerator water filter located?
The water filter for your refrigerator is typically located inside the refrigerator, either in the top right corner, the bottom right corner, or the back wall of the refrigerator. The water filter may also be located in the base grill of the refrigerator.
To find your filter, you may need to remove drawers and shelves or open the kickplate (panel under the door) to locate it. Once you find the filter, it should be easy to remove and replace.
How do you remove a water filter cover?
Removing a water filter cover is dependent on the type of water filter you are using as well as the manufacturer. Generally, water filter covers are removed either by unscrewing the cover or by twisting and pulling off the cover.
To be sure of the correct process for removing your water filter cover, check the manual that came with the filter and follow the instructions for your model.
If you don’t have the manual, most covers are unscrewed by turning the cover counterclockwise with a flathead screwdriver. You will need to apply some pressure in order to loosen the cover, so use an appropriately sized screwdriver that can fit into the notches of the cover.
If the cover does not unscrew easily, try alternating placing pressure on one side of the cover, then the other. Once the cover has been unscrewed, gently lift it up with your hands to expose the filter.
If your water filter cover is a twist-off type of cover, grip the filter firmly with both hands and turn the filter in a counterclockwise direction until it starts to come loose. Then, twist and pull the filter off with your hands.
The filter should come off relatively easily, but if there is any resistance, gently twist the filter until it is completely removed.
It is important to make sure that the cover is securely and correctly replaced when you have finished changing the filter. When replacing the cover, start by aligning the notches or grooves of the cover with the filter.
Then twist or screw the cover back on until it is snug and secure. Check the manual if you have any questions about replacing the filter cover.
How do you remove the cover on a Whirlpool water dispenser?
Removing the cover of a Whirlpool water dispenser can be done fairly simply. First, locate the cover at the top of the dispenser and press in on the tabs located on either side. The cover should then pop off so you can access the controls inside.
From there, carefully remove any screws that may be securing the cover, and then lift it off. Depending on the model of Whirlpool water dispenser, there may be additional screws or parts that need to be removed in order to access the controls.
Be sure to keep track of any screws, as they will need to be replaced during assembly.