Removing the stopper from a bathtub lift and turning it can be a relatively simple job if you know where to look. The first thing to do is to locate the bathtub lift, which is usually situated near the bathtub faucet.
Once it’s located, you’ll need to locate the stopper. It will either be a large, plastic piece attached to the bathtub lift or it may be a metal piece that is screwed into the underside of the bathtub lift.
Next, you’ll need to remove the stopper. To do this, you may need to use a screwdriver to loosen any screws that are securing it to the bathtub lift. Once it is loose, you should be able to pull it away from the lift with your fingers.
After that, you’ll need to turn the stopper. If it is a plastic stopper, you may be able to do this simply by hand. However, if it is a metal stopper, you may need to use pliers to turn it to the desired position.
Once it is in the desired position, you may need to tighten the screws to make sure the stopper stays in the desired position.
And that’s it! With a few simple steps, you can successfully remove the stopper from a bathtub lift and turn it to the desired position.
How do you remove a lift -&- turn tub stopper?
Removing a lift-and-turn tub stopper will vary slightly from model to model, but in general, the process generally requires the following steps:
1. Locate the screw holding the stopper in place. This screw is usually located near the drain, and it has a knob or handle that must be unscrewed.
2. Remove the screw and set it aside (it will be needed to install the new stopper).
3. Grip the stopper with your hand and gently twist it counterclockwise to loosen it. Some models may require a pair of locking pliers.
4. Once the stopper is loose, pull it straight out of the drain. Be gentle with this step since the stopper may be made of fragile or delicate material.
5. If necessary, remove any residue or buildup from the drain flange with a cloth or scrub brush.
6. Install the new stopper by reversing the steps above. Make sure the drain flange is clean and that the stopper fits snugly into the drain before tightening the screw.
How do you remove the tub plug that twists up and down?
Removing a tub plug that twists up and down depends on the type of plug. For some plugs, a flathead screwdriver can be used to pry the plug from its base. For other plugs, an adjustable wrench may be necessary to loosen the bolt securing the plug in place.
If the bolt has corroded, mineral oil or lubricating oil can be applied to help loosen it.
Once the bolt is removed, the plug should be able to be pulled straight up. If there is a stopper attached to the plug, it may need to be removed or cleaned before the plug can be removed. If the stopper is corroded, baking soda, vinegar, or a rust-removal product can be helpful.
Once the plug has been removed, the hole can be cleaned with a brush and mild soap. A new plug and washer can then be inserted and tightened using the same tools that were used to remove the old plug.
How do you unclog a lift and turn drain?
To unclog a lift and turn drain, the following steps should be taken:
1. Begin by turning off the water supply to the drain in order to make sure there’s no backflow when draining the sink.
2. Use a bucket to catch any water still in the drain. Take off the lift and turn the drain cover and remove any debris that you may find in the drain.
3. Take a plunger and place it over the drain. Fill the bucket with water and then place the plunger over the drain. Make sure to create a tight seal with the plunger and the drain so that it creates a vacuum effect.
4. Begin plunging vigorously. The vacuum effect created by the plunger should help force out any clog that may be blocking the drain. Keep plunging until the clog is released from the drain.
5. Once the clog has been removed, remove the plunger and check the drain to see if the clog has been successfully released. If you’re still having issues, you can use a snake or auger to try and fish out any remaining debris.
6. Once the clog is out of the way, reinstall the lift and turn drain cover, and turn the water back on. Give the drain a few minutes to fill up and test it to see if the clog has been fully removed.
If the clog persists or the drain still isn’t functioning properly, you may need to call a professional to help get your drain cleared.
What are the different types of bathtub drain stoppers?
They range from basic mechanical stoppers to more advanced models with features such as adjustable water flow and overflow protection.
One of the most common types is the basic Lift & Turn style, which manually opens and closes the drain. This style requires you to use a tool like a screwdriver to turn a center knob, which then releases a lock and lifts the stopper out of the way.
This is a relatively inexpensive option and is popular for homes on a budget.
Another option is the Toe Touch stopper, which is operated by pushing a button or lever on the side of the tub. This style also lets you control the amount of water that comes out of the drain, allowing you to reduce water waste when filling the tub.
However, this style can be prone to clogs and may require more frequent maintenance than other types of stoppers.
Pop-up stoppers are often found in hotels and are operated with a knob on the center of the bathtub drain. They’re designed to fit seamlessly into the tub so that it doesn’t detract from the overall look.
They are more expensive than basic mechanical stoppers, and require some knowledge of plumbing.
Finally, a third style of bathtub drain stopper is the Trip Lever. This type is usually operated by a lever placed on the side of the bathtub, allowing you to adjust the amount of water that flows out of the drain.
This is the most expensive type of stopper, but it is also the most efficient and eco-friendly.
How do you get a bathtub plug out?
To get a bathtub plug out, you will need to identify the type of plug that you have. Most bathtub plugs are one of two types; a “cup-style” plug which is held in place with a spring washer, or a “wire-style” plug which is using a spring tension to hold it in place.
For the cup-style plug, you will need an adjustable wrench or channel locks. Place the adjustable wrench or channel locks over the cup plug, and gently twist the tool to loosen the plug. Once it has been loosened, you can then use your hands to remove it.
For the wire-style plug, you will need a pair of needle-nose pliers. Place the needle-nose pliers over the wire, and gently pull outward. This should loosen the plug, which you can then remove by hand.
If the plug is corroded or stuck, you may need to use a lubricant such as WD-40 or oil to loosen it. Additionally, if you don’t have the right tools, you can attempt to remove the plug using a screwdriver – be sure to use a flat-head screwdriver, and do not apply too much force as you could damage the plug.
It is important to remember that if you choose to remove a bathtub plug yourself, you are doing so at your own risk. If you are unsure or uncomfortable attempting it yourself, it is recommended that you contact a professional plumber to do the job correctly and safely.
What do plumbers use to unclog tub drains?
Plumbers use a variety of tools to clear a clogged bathtub drain. Depending on the severity and cause of the clog, they may use a plunger with extended handle, a hand or power auger, a plumber’s snake, or a commercial chemical drain cleaner.
To clear a minor clog, a plunger is typically the tool of choice, as it is quick, easy, and can usually get the job done. To tackle more severe blockages, a hand or power auger can be used to work its way down the pipe and break up any obstructions.
The plumber’s snake is an even more effective option for clearing large clogs and is used in situations where other tools fail. Finally, in instances where a clog is deep in the drain’s pipes, a chemical drain cleaner may be used to dissolve the clog and restore normal flow.
Plumbers use these tools in combination with their knowledge and experience to get the job done in a quick and effective manner.
Can drain covers be removed?
Yes, drain covers can be removed. In certain cases, it may actually be necessary to remove one. For example, if a drain is clogged, the cover may have to be removed in order to access the clog and unblock it.
In other cases, drain covers may need to be removed in order to access the pipes underneath. This may be necessary for plumbing repair or maintenance.
If a drain cover must be removed, it should be done with caution since the cover may be heavy or have sharp edges. It also helps to have the right tools for the task to avoid damaging the cover or the pipes.
Furthermore, when the drain cover is being replaced, it should be done securely so it is level with the rest of the surface and won’t pose a hazard to anyone.
How do you unclog a tub with a plunger that doesn’t work?
If a plunger does not unclog a bathtub, you can try a variety of other methods before calling a plumber. Start by pouring a few gallons of hot water down the drain in an effort to melt away clogs. If this doesn’t work, try using a drain snake to manually remove any blockages.
This can generally be done without the need to use any dangerous chemicals. If neither of these methods work, try using a combination of baking soda and vinegar. When combined, these two ingredients create a reaction that can help release blockages.
If all else fails, you may need to contact a plumber for assistance.
Can you pour Drano into a tub with standing water?
No, it is not safe to pour Drano into a tub with standing water. Drano is a chemical product specifically designed to unclog pipes and should not come into contact with standing water. If Drano is poured into a tub with standing water, it could cause the water to bubble up, creating a caustic slurry that can splatter and burn the skin or eyes.
Additionally, Drano contains sodium hydroxide, which can be hazardous if it comes in contact with skin or is swallowed. It can result in nausea, difficulty breathing, and abdominal pain. It is best to use caution when using Drano to unclog pipes and not to pour it directly into standing water.
How do you unclog a bathtub drain without removing the stopper?
There are numerous ways to unclog a bathtub drain without removing the stopper. Here are a few common methods you can try:
1. Boiling Water: Boiling a pot of hot water and pouring it directly down the bathtub drain can help to dislodge stuck on clogs. It’s important to pour the boiling water slowly to ensure that the drain is not damaged.
2. Baking Soda and White Vinegar: Pour about half a cup of baking soda down the drain followed by a cup of white vinegar. Allow the fizzing mixture to sit for a few minutes before running hot water down the drain.
3. Plunger: It may be possible to use a plunger to dislodge a clog. Be sure to cover the overflow outlet with a wet rag before plunging.
4. Bent Wire Hanger: This can be a tricky method but it could work. Use an old wire hanger to carefully try and dislodge the clog by reaching down into the drain. Be sure to be cautious with this method so as not to do any damage.
5. Chemical Drain Cleaners: This can be an effective way to unclog a bathtub drain however, it’s important to read and follow the directions on the packaging of the product carefully and use it in a well-ventilated area.
Are bathtub drain stoppers universal?
No, bathtub drain stoppers are not universal. Depending on the type of bathtub and drain, the design and type of stopper can vary greatly. There are generally two categories of tub drains: lift and turn and ‘pop up’ drains.
Lift and turn drains will require a stopper that screws directly into the drain assembly. This type of stopper typically comes in two types: dome and ‘wafer’ style. The dome tends to be more versatile since it comes in a variety of shapes and sizes that can fit any type of tub.
The wafer style is more specific and will only fit a certain type of shaped drain.
Pop up drains require a stopper that sits in the drain opening and has a metal rod that goes through the body of the stopper. These usually come in two designs: flat and button style. The flat style is usually used on plastic tubs and the button style is normally used with more traditional metal tubs.
Because of the wide variety of drains, it is impossible to have a universal bathtub drain stopper that will fit any type of tub. It is important to take measurements of the tub and drain before purchasing a new stopper.
That way, you can ensure that you are buying the right one.
What size bathtub drain stopper do I need?
The size of bathtub drain stopper you need will depend on the size and shape of the bathtub drain opening. Generally if the drain opening is 1 3/8 inches or smaller you will need a 1 1/2 inch drain stopper.
If it is larger than 1 3/8 inches, you will likely need a 2 inch drain stopper. Before purchasing your bathtub drain stopper, it is highly recommended to measure the drain opening with a ruler or tape measure to ensure you are purchasing the correct size.
Additionally, some bathtub drains may require a special type of stopper in order to properly close. Therefore, it is best to consult with a knowledgeable sales representative in a local home improvement store before making a purchase.
Can you replace the drain stopper in a bathtub?
Yes, it is possible to replace the drain stopper in a bathtub. It typically involves unscrewing the existing drain and removing it from the drain pipe. You will then need to purchase a new drain and stopper assembly.
A 10-year old or newer bathtub usually requires a trip lever drain assembly. After selecting the correct drain for your tub, the assembly needs to be installed in the overflow opening. The drain you choose should be durable and made of the same material as the tub.
After the drain and stopper are positioned into the drain pipe and the linkage is attached to the trip lever hole, the installation can be further secured with a few screws. Once the drain assembly is tightened, you can fill the tub with water to make sure it is functioning properly.
What can I use instead of a tub stopper?
If you don’t have a tub stopper or don’t want to use one, there are a few different alternatives you can try. One option is to use an inflatable stopper. These are usually made of latex or vinyl and simply inflate in the drain to create a waterproof seal.
Alternatively, a drain plug or drain strainer could be used. Drain plugs come in many different shapes and sizes and essentially just plug the drain to stop the water from going down. Drain strainers are essentially the same but allow water to pass through them while catching debris before it gets into the drain.
Finally, you could also use some items you have at home such as a wash cloth or sponge. These will get wet while in the drain, but they could provide enough of a seal to keep the water from running down.